PERLESMITH PSCLF1 Corner TV Wall Mount Instruction Manual
- May 15, 2024
- Perlesmith
Table of Contents
INSTRUCTION MANUAL
PSXLF1
Rev00 Full-
Motion TV Wall Mount
PSCLF1 Corner TV Wall Mount
CAUTION
PLEASE READ ENTIRE MANUAL PRIOR USE AND SAVE THESE INSTRUCTIONS.
Before getting started, make sure this mount is compatible.
-
Is the VESA pettem Of your TV within the MIN and MAX sizes? Compatible VESA patthern:
Compatible| VESA patthern:
---|---
200 x 100mm| A00 x 200mm
200 x 200mm| A00 x 400mm
300 x 200mm| 600 x 200mm
300 x 300mm| 600 x 800mm
| 600 x 400mm -
Does your TV (including accesso— ries) weigh less than 99 Ibs (45kg)? Yes – Perfect!
No -This mount is NOT compatible.
WARNING
DO NOT exceed the Max load indicated. Use with products heavier than the Max load may result in failure of the mount, which could cause damage or injury. -
What is your wall made of?
-
Tools Needed (Not Included)For Wood Stud Walls For Solid Concrete and Brick Walls
-
Improtant Safety Information
• This product is designed for installation on wood stud, solid concrete and brick walls. DO NOT install on drywall alone.
• The wall must be capable of supporting four times the weight of the TV and mount combined.
• This product contains small parts that may pose a choking hazard.
• Avoid the risk of personal injury or property damage!
• Do not use this product for any purpose that is NOT explicitly specified in this manual. Do not exceed the maximum weight capacity. We are not liable for damage or injury caused by incorrect assembly, improper mounting, or inappropriate use.
• Before starting assembly, verify that all parts are included and undamaged.
Do not use damaged or defective parts. If you require replacement parts, please call technical support or email customer service.
WARNING: All fasteners must be firmly tightened!
Supplied Parts and Hardware CAUTION!
This anchor is for concrete or brick walls ONLY. DO NOT use them in drywall or
wood studs.
Step 1 Attach the TV Brackets to the TV
1-1 Select TV Bolts 1-2 Select TV Bolt Length and Spacer
Combination
a No spacers are needed
Flat Back TV
Spacers are not necessary
b Spacers are needed
Flat Back TV
With extra space needed Rounded or Irregular Back TV
TV brackets can not rest flat on your TV 1-3 Secure the TV Brackets to the TV
Round
holes should be directed toward the top of the TV.
a No spacers are needed b Spacers are needed Step 2 Mount the Arm
Assembly / Wall Plate on the Wall
WARNING:
- Avoid the risk of personal injury or property damage!
- Tighten the lag screws only until they are pulled firmly against the wall plate (DO NOT overtighten).
- Do not use a drill to tighten the lag screws and only use a socket wrench.
For Wood Studs Installation:
Follow Page 08 CAUTION
- Minimum wood stud size: 1 1/2” Wx 3 1/2” D (38 x 89mm).
- Wall panel material must not exceed 5/8” (16mm).
- TIP: Once you find the stud locations, set the mount on the floor and line up each wall plate with the studs. This will help you determine whether the mount will fit in the corner with your TV as desired.
Tools Needed (Not Included) For Concrete Installation:
Follow Page 09 CAUTION Tools Needed (Not Included) Common
Installation Tools (Not Included) Step 3 Verify that the Arm Assembly is
Firmly Mounted Step 4 Install the Front Support AssemblyStep 5 Secure the Front Support Assembly onto the Arm Assembly /
Wall Plate Remove the pre-assembled bolts [H3] and
washers [H4].Hang the front support on the arm assembly /
wall plate. Tighten the bolts [H3] and washers [H4] to secure them.
Step 6 Hang the TV on the Front Support Assembly Remove 2 pre-assembled bolts [H5]. Flip
the safety locks up.Hang the TV on the front support using the hooks on
the brackets. Close the safety locks by firmly tightening bolts [H5].
Step 7 Adjustment Tilt Adjustment Slightly loosen the
tilting nuts [T].
Adjust TV to the desired angle, and then fully tighten the tilting nuts again
to lock the tilt angle.
Level Adjustment Slightly loosen the bolts [H3]. Level the TV, and then
retighten the bolts to hold the TV in position.
TIP:
Use the level [06] to assist with adjustments.
Step 8 Adjust the Swivel Angle of the TV
FAQs
Question 1 How should | manage the cables?
Answer: Use the cable ties.
Question 2 How do I find the right height for mounting the TV?
Answer: The simplest method is to position the TV so that the center is the same height as your eye level while viewing. Scan the QR code to watch the mounting video, which covers this in more detail.
Question 3 It’s too hard to adjust the swivel angle or extension of the TV Wall Mount.
1 Mount the TV and Wall Mount on the wall before trying to move the arms. Only move the TV by the left and right edges. Do not push on the screen of the TV. 2 If you have tried Option 1 but adjustment is still too hard, try lubricating the arm joints with a few drops of machine oil.
Question 4 How can | raise/lower the TV if the TV Wall Mount is already fixed on the wall?
Answer: Step 1: Remove the TV from the TV Wall Mount. Step 2: Remove the TV brackets from the TV and reattach according to instructions A or B in the picture below (A for lifting up the TV or B for lowering the TV). Step 3: Hang the TV on the TV Wall Mount and secure. 1 To raise the TV by a few inches, reattach theTV brackets using the upper holes in the brackets. 2 To lower the TV by a few inches, reattach the TV brackets using the lower holes in the brackets.
1-800-556-6806 (US/CA)
44-808-196-3891 (UK)
www.perlesmith.com
supportus@perlesmith.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>