DV8 SPBR-03 Ford Bronco Rear Differential Skid Plates Instruction Manual
- June 13, 2024
- DV8
Table of Contents
DV8 SPBR-03 Ford Bronco Rear Differential Skid Plates
Product Information
- Product: Rear Axle / Differential Skid Plate
- Model: 2021+ Bronco SPBR-03
- Manufacturer: DV8 Offroad
- Contact: 855-680-9595
- Website: www.dv8offroad.com
Product Usage Instructions
Tools Required:
- Ratchet
- 10mm and 13mm Socket
Skill Level: Novice/Intermediate – 1 (you) to 2 persons
Little skill level required, you can easily install it by yourself; however,
additional help will be useful.
Time Required: 1.5 hours
Time to install this should only take about 1.5 hours.
Warnings/Cautions Before Starting Installation:
-
Read and understand all instructions, warnings, cautions, and notes contained in this installation instruction guide.
-
Consult your vehicle owner’s manual for proper disconnection of electrical and lifting of vehicle if required for installation of this product.
-
This install may require some technical skills and knowledge of basic mechanical work. If you do not feel capable of performing this install, please take this product to a trained
professional. -
Contact customer service with any questions or concerns before installing the product: 855-680-9595
-
DV8 Offroad is not responsible for any bodily injury or harm to you or your vehicle as a result of an improper install.
-
Proper installation of this kit requires knowledge of the factory recommended procedures for removal and installation of original equipment components.
-
We recommend having the factory shop manual and any special tools needed to service your vehicle on hand during the installation.
-
Installation of this kit without proper knowledge of the factory recommended procedures may affect the performance of these components and the safety of the vehicle.
-
Inspect all contents of this package to make sure the product is not damaged and all installation hardware has been included.
-
If parts are missing from the kit, please provide the following information: 1. Name of purchase location, 2. Bar Code on side of box, 3. Date above bar code, 4. Date inside box cover.
Installation Manual
Step 1:
Begin by unpacking all items and inspecting for missing pieces or damage.
If you have any concerns, please contact the company the product was purchased
from.
Hardware Included:
- (6) M8x30
- (6) M8 Flat Washers
- (6) M8 Split Washers
- (2) M6x20
- (2) M6 Flat Washers
- (2) M6 Split Washers
Step 2:
Begin by removing two bolts from the differential.
Step 3:
Slide the nut plate into the upper link mount. Note that there are two
small tabs to hold the nut plate in place.
Step 4:
Raise the skid plate to the vehicle and loosely secure it to the
differential using a 13mm socket and the provided M8 hardware.
Step 5:
Loosely secure the sides of the skid plate to the nutplate in the upper
link mount using a 13mm socket and the provided M8 hardware.
Step 6:
Install the tabs and secure them to the skid plate using a 10mm socket and
the provided M6 hardware.
Step 7:
Using a 13mm socket, secure the M8 bolts on the differential skid and
torque them to 33ft lbs. Secure the hardware to the nutplates on both sides of
the skid plate using a 13mm socket.
If you need further assistance, please contact customer service at 855-680-9595.
REAR AXLE / DIFFERENTIAL SKID PLAT
2021+ Bronco SPBR-03
TOOLS REQUIRED
- Ratchet
- 10mm,13mm Socket
SKILL LEVEL
- Novice/Intermediate
- 1 (you) to 2 persons
Little skill level required, you can easily install it by yourself however, additional help will be useful
TIME REQUIRED
- 1.5 Hours
Time to install this should only take about 1.5 hours.
WARNINGS/CAUTIONS BEFORE STARTING INSTALLATION
- Before you install this kit — Read and understand all instructions, warnings, cautions, and notes contained in this installation instruction guide. Consult your vehicle owner’s manual for proper disconnection of electrical and lifting of vehicle if required for installation of this product.
- This install may require some technical skills and knowledge of basic mechanical work. If you do not feel that you are capable of performing this install please take this product to a trained professional.
- After reading this guide please contact us with any questions or concerns before installing product.
- Customer Service: 855-680-9595
- DV8 Offroad is not responsible for any bodily injury or harm to you or your vehicle as a result of an improper install.
Proper installation of this kit required knowledge of the factory recommended procedures for removal and installation of original equipment components. We recommend that the factory shop manual and any special tools needed to service your vehicle be on hand during the installation. Installation of this kit without proper knowledge of the factory recommended procedures may affect the performance of these components and the safety of the vehicle
Always wear eye protection when operating power tools
Inspect all contents of this package to make sure product is not damaged and
all installation hardware has been included. If parts are missing from kit,
please be prepared to provide the following information
- Name of purchase location
- Bar Code on side of box
- Date above bar code
- Date inside box cover
INSTALLATION
STEP 1
Begin by unpacking all items and inspecting for missing pieces or damage. If
you have any concerns, please contact the company the product was purchased
from.
Hardware Included:
- (6) M8x30
- (6) M8 Flat Washers
- (6) M8 Split Washers
- (2) M6x20
- (2) M6 Flat Washers
- (2) M6 Split Washers
STEP 2
Begin by removing two bolts from the differential.
-
STEP 3
Slide the nut plate into the upper link mount.
NOTE: There are two small tabs to hold he nut plate in place.
-
STEP 4
Raise the skid plate to the vehicle and loosely secure to the differential using a 13mm socket and provided M8 hardware.
-
STEP 5
Loosely secure the sides of the skid plate to the nutplate in the upper link mount using a 13mm socket and provided M8 hardware.
-
STEP 6
Install the tabs and secure to the skid plate using a 10mm socket and provided M6 hardware.
-
STEP 7
Using a 13mm socket, secure the M8 bolts on the diff skid and torque to 33ft lbs. Secure hardware to the nutplates on both sides of the skid plate using a 13mm socket.
-
STEP 8
Double check fitment and all hardware is secure.
NEED HELP?
855-680-9595
6400 SYCAMORE CANYON BLVD. RIVERSIDE, CALIFORNIA 92507
855-680-9595
WWW.DV8OFFROAD.COM
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>