DV8 OFFROAD SRGL-01 Bed Protection Skid Installation Guide
- June 9, 2024
- DV8 OFFROAD
Table of Contents
PRODUCT
INSTALLATION MANUAL
Bed Protection Skid
2020+ Jeep Gladiator
SRGL-01
SRGL-01 Bed Protection Skid
TOOLS REQUIRED
– Ratchet
– 16mm Socket
– 18mm Socket
SKILL LEVEL
– Novice/Intermediate
– 1 (you) to 2 persons
Little skill level required, you can easily install it by yourself however,
additional help will be useful
TIME REQUIRED
– Approximately: 1.5 Hours
Time to install this should only take approximately 1.5 hours.
WARNINGS/CAUTIONS BEFORE STARTING INSTALLATION
Before you install this kit — Read and understand all instructions,
warnings, cautions, and notes contained in this installation instruction
guide. Consult your vehicle owner’s manual for proper disconnection of
electrical and lifting of vehicle if required for installation of this
product. This install may require some technical skills and knowledge of basic
mechanical work. If you do not feel that you are capable of performing this
install please take this product to a trained professional.
After reading this guide please contact us with any questions or concerns
before installing product.
Customer Service: 855-680-9595
DV8 Offroad is not responsible for any bodily injury or harm to you or your
vehicle as a result of an improper install.
Proper installation of this kit required knowledge of the factory recommended
procedures for removal and installation of original equipment components. We
recommend that the factory shop manual and any special tools needed to service
your vehicle be on hand during the installation. Installation of this kit
without proper knowledge of the
factory recommended procedures may affect the performance of these components
and the safety of the vehicle
Always wear eye protection when operating power tools
Inspect all contents of this package to make sure product is not damaged and
all installation hardware has been included. If parts are missing from kit,
please be prepared to provide the following information
- Name of purchase location
- Bar Code on side of box
- Date above bar code
- Date inside box cover
STEP 1
Begin by unpacking all items and inspecting for missing pieces or damage. If
you have any concerns, please contact the company the product was purchased
from.
Hardware Included:
(12) M12x35 Bolts
(12) M12 Flat Washers
(12) M12 Lock washers
(6) M10x35 Bolts
(6) M10 Flat Washers
(6) M10 Lock Washers
STEP 2
Using a 16mm socket and provided M10x35 hardware, line up the bracket to the
frame and loosely install the first two bolts closest the rearbumper.
NOTE: All brackets included are directional and will only fit properly on
a specific side of the vehicle. Take note of the orientation of our brackets
duringinstallation.
STEP 3
Install the third M10 bolt by placing the provided nutplate inside the frame
through the opening in the bottom of the frame.
STEP 4
Secure the bolts with a 16mm socket.
STEP 5
Attach the slider to the rail bracket using an 18mm socket and provided M12
hardware.
NOTE: One of the bolts is obstructed by the exhaust and it may be
necessary to hold it out of the way and use a 18mm wrench. An extra pair of
hands will make this process easier.![DV8 OFFROAD SRGL 01 Bed Protection Skid
- fig 4](https://manuals.plus/wp-content/uploads/2023/01/DV8-OFFROAD-SRGL-01 -Bed-Protection-Skid-fig-4.png)
STEP 6
Repeat steps 1-5 on the other side of the vehicle.
STEP 7
Check fitment against body and that the sliders are not making contact. Ensure
all hardware is secure.
855-680-9595
NEED HELP?
Documents / Resources
| DV8
OFFROAD SRGL-01 Bed Protection
Skid
[pdf] Installation Guide
SRGL-01 Bed Protection Skid, SRGL-01, Bed Protection Skid, Protection Skid,
Skid
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>