DV8 Offroad UNSK-01 Elite Series D Ring Shackles Instruction Manual

DV8 Offroad UNSK-01 Elite Series D Ring Shackles

Product Information

Specifications

• Product: Elite Series D-Rings UNSK-01 (BL, RD, GR)
• Manufacturer: DV8 Offroad
• Address: 6400 Sycamore Canyon Blvd. Riverside, California 92507
• Contact: 855-680-9595

Product Usage Instructions

Tools Required

• 3/8 Ratchet / Impact

Skill Level
Easy – Suitable for one person with little skill level required. Installation can be done independently.

Time Required
Approximately 3 minutes per side, totalling about 6 minutes for complete installation.

Warnings/Cautions Before Starting Installation

• Before beginning the installation, ensure to read and understand all instructions, warnings, cautions, and notes provided in the installation guide. Refer to the vehicle owner’s manual for necessary precautions and procedures.
• Technical skills and basic mechanical knowledge may be required for the installation. If unsure, seek professional assistance.
• Contact customer service at 855-680-9595 for any queries or concerns prior to installation.

Proper Installation
Follow factory-recommended procedures for component removal and installation. Have the factory shop manual and any special tools ready for the process.

Installation Steps

• Step 1
  Unscrew the pin from the shackle and remove the four isolators from the pin using a 3/8 tool if needed.

• Step 2
  Select appropriate isolators based on bumper D-Ring mount thickness. Fit isolators between the bumper mount and shackle.

• Step 3
  Feed the pin through the shackle and isolators. Secure the pin by screwing it into the shackle.

• Step 4
  Tighten the pin using a 3/8 ratchet/chuck until secure. Ensure the pin is tight enough to prevent loosening by hand.

FAQ

• Q: What should I do if any parts are missing from the kit?
  A: If parts are missing, provide the following information to the manufacturer:

1. Name of purchase location
2. Bar Code on side of box
3. Date above bar code
4. Date inside box cover

TOOLS REQUIRED

• – 3/8” Rachet / Impact

SKILL LEVEL

• Easy
• 1 (you) person
  Little skill level required, you can easily install it by yourself.

TIME REQUIRED

• 3 minutes per side.
  Time to install this should only take about 6min total.

WARNINGS/CAUTIONS

• Before you install this kit — Read and understand all instructions, warnings, cautions, and notes contained in this installation instruction guide. Consult your vehicle owner’s manual for proper disconnection of electrical and lifting of vehicle if required for installation of this product.

• This install may require some technical skills and knowledge of basic mechanical work. If you do not feel that you are capable of performing this install please take this product to a trained professional.

• After reading this guide please contact us with any questions or concerns before installing the product.
  Customer Service: 855-680-9595

• DV8 Offroad is not responsible for any bodily injury or harm to you or your vehicle as a result of an improper installation.

• Proper installation of this kit required knowledge of the factory-recommended procedures for removal and installation of original equipment components. We recommend that the factory shop manual and any special tools needed to service your vehicle be on hand during the installation. Installation of this kit without proper knowledge of the factory-recommended procedures may affect the performance of these components and the safety of the vehicle

  • Always wear eye protection when operating power tools
    Inspect all contents of this package to make sure the product is not damaged and all installation hardware has been included. If parts are missing from the kit, please be prepared to provide the following information
  1. Name of purchase location
  2. Bar Code on side of box
  3. Date above bar code
  4. Date inside box cover

INSTALLATION INSTRUCTION

Begin by unpacking all items and inspecting for missing pieces or damage. If you have any concerns, please contact the company the product was purchased from. Extra hardware may be included with the product.

HARDWARE INCLUDED:

• (4) 1/8” Isolators
• (4) 3/16” Isolators
• (2) 7/16” Pin

STEP 1 | Unscrew the pin from the shackle and remove the four isolators from the pin. You may be able to do this by hand, if not use your 3/8” tool.

STEP 2 | Identify what isolators will be used by holding up the shackle and fitting the isolators between the outside of your bumper mount and the inside of the shackle.
NOTE: Different variations of isolators will be used based on the thickness of your bumper D-Ring mount. In our case, our 1” thick D-Ring mount accepted both 1/8” isolators.

STEP 3 | Once isolators have been selected, hold up the shackle and isolators, and feed the pin through the shackle.
Once it bottoms out, begin screwing it into the shackle.

STEP 4 | Using a 3/8” ratchet/chuck, being to tighten the pin into the shackle until secure. The pin should be tight enough that the pin cannot be loosened by hand.
NOTE: The opening in the pin may have some slack around a 3/8” rachet/chuck since it is also designed to be used with factory tyre changing posts (not all applications will work).

STEP 5 | Double check both pins are secure, and you are ready to put your new Elite Series D-Ring to the test!

NEED HELP? 855-680-9595

6400 SYCAMORE CANYON BLVD.
RIVERSIDE, CALIFORNIA 92507
855-680-9595
WWW.DV8OFFROAD.COM

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>