DV8 OFFROAD DMT3-01 Digital Device Dash Mount Instruction Manual
- June 13, 2024
- DV8 OFFROAD
Table of Contents
PRODUCT
INSTALLATION MANUAL
DMT3-01 Digital Device Dash Mount
4 RUNNER DASH MOUNT
2010+ (5TH GEN) TOYOTA 4RUNNER
DMT3-01
TOOLS REQUIRED
- Drill
- 3mm, 4mm Allen Bit
- 10mm Wrench
- 10mm Socket
- Trim Clip Tool
- 11/32” Drill Bit
SKILL LEVEL
- Novice/Intermediate
- 1 (you) to 2 persons
Little skill level required, you can easily install it by yourself however, additional help will be useful
TIME REQUIRED
- 1 Hour
Time to install this should only take about an hour
WARNINGS/CAUTIONS BEFORE STARTING INSTALLATION
Before you install this kit — Read and understand all instructions, warnings,
cautions, and notes contained in this installation instruction guide. Consult
your vehicle owner’s manual for proper disconnection of electrical and lifting
of vehicle if required for installation of this product.
This install may require some technical skills and knowledge of basic
mechanical work. If you do not feel that you are capable of performing this
install please take this product to a trained professional.
After reading this guide please contact us with any questions or concerns
before installing product.
Customer Service: 855-680-9595
DV8 Offroad is not responsible for any bodily injury or harm to you
or your vehicle as a result of an improper install.
Proper installation of this kit required knowledge of the factory recommended
procedures for removal and installation of original equipment components. We
recommend that the factory shop manual and any special tools needed to service
your vehicle be on hand during the installation. Installation of this kit
without proper knowledge of the factory recommended procedures may affect the
performance of thesecomponents and the safety of the vehicle
- Always wear eye protection when operating power tools
Inspect all contents of this package to make sure product is not damaged and all installation hardware has been included. If parts are missing from kit, please be prepared to provide the following information
- Name of purchase location
- Bar Code on side of box
- Date above bar code
- Date inside box cover
Begin by unpacking all items and inspecting for missing pieces or damage. If you have any concerns, please contact the company the product was purchased from.
HARDWARE INCLUDED
(2) M6x15 Allen
(2) M6x30 Allen
(4) M6 Flat Washers
(4) M6 Nylon Lock Nuts
(2) M5x10
(2) M5 Flat Washers
STEP 1 | Remove the side trim pieces by pulling towards the rear of the
vehicle.
These can be a little difficult to remove.
Use a trim clip to apply pressure to the clips behind the trim, while pulling
on it, if necessary. STEP 2 | Remove the control cluster by pulling towards
the rear of the vehicle to release the clips, and disconnect the wiring
connector on the back.
STEP 3 | Slide the two M6x30 bolts through the dash mount and place it in the
desired install location.
When it is adjusted as desired, use a 4mm allen bit to spin the bolts so they
make marks on the dash for drilling.
Use a sharpie to mark the side mounting holes for drilling. STEP 4 | Remove
the dash piece to prepare for drilling by removing the four bolts securing it
using a 10mm socket.
STEP 5 | Drill out the marked holes using an 11/32” drill bit.
STEP 6 | Install the dash mount onto the dash piece using the provided M6
hardware with a 4mm allen bit and 10mm wrench.
The longer M6x30 hardware will be used for the top mounts and the shorter
M6x15 hardware will be used to secure the sides. STEP 7 | Re-install the top
dash piece using a 10mm socket and factory hardware. STEP 8 | Install the
control cluster and dash trim by applying pressure until the clips are
secured. STEP 9 | If desired, install the armsonto the dash mount using the
provided M5 hardware and a 3mm allen bit. STEP 10 | Congrats! You are finished
with the install of the 2010+ (5th Gen) Toyota 4Runner Dash Mount!
NEED HELP?
855-680-9595
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>