CHORS 41.4102 Hanging Lamp Instruction Manual

CHORS 41.4102 Hanging Lamp

Product Information

• The product is called “Accent Z” and it comes in four different models: Accent Z 60, Accent Z 90, Accent Z 120, and Accent Z 150.
• Each model has a unique code starting with “41.41XX” followed by a specific number for each model.
• The electrical wiring diagrams are provided in the user manual for reference.

Product Usage Instructions

1. Determine the specific model of your Accent Zproduct by referring to the code mentioned in the user manual. Thecode will start with “41.41XX” followed by a specific number foreach model (60, 90, 120, or 150).
2. Measure the dimensions of your Accent Z product to ensure proper installation and compatibility with your intended application.
3. Connect the product to a suitable power supply. There are three power supply options available: LED Power Supply, TRIAC, and DALI. Choose theappropriate power supply option based on your requirements and the availability of compatible power sources.
4. Follow the provided electrical wiring diagrams to correctly connect the product to the chosen power supply. Make sure to match the corresponding terminals (L, N, +, -) of the product and power supply.
5. In case of any doubts or uncertainties during installation, refer to the user manual for further guidance or contact the manufacturer’s customer support for assistance.
6. Once the product is properly installed and connected to the power supply, it is ready for use. Ensure that the power supply is providing the required voltage (230V) and frequency (50Hz) for optimal performance.
7. To turn the product on  or off, refer to the specific control mechanism provided with yourAccent Z product. This may involve using a switch, remote control, or other designated controls.
8. Enjoy the benefits and features offered by your Accent Z product according to your intended application and lighting needs.

Note: Always prioritize safety when installing or operating electrical products. If you are unsure about any aspect of the installation process, consult a qualified electrician.

MOUNTING HOLES

The product dimensions vary depending on the model:

• Accent Z 60: 41.4102.xxx.xxx
  X| Y| Z
  ---|---|---
  471 mm| 64,5 mm| 50 mm
• Accent Z 90: 41.4103.xxx.xxx
  X| Y| Z
  ---|---|---
  771 mm| 64,5 mm| 50 mm
• Accent Z 120: 41.4104.xxx.xxx
  X| Y| Z
  ---|---|---
  1071 mm| 64,5 mm| 50 mm
• Accent Z 150: 41.4105.xxx.xxx
  X| Y| Z
  ---|---|---
  1371 mm| 64,5 mm| 50 mm

ELECTRICAL WIRING DIAGRAMS

• ON/OFF 41.41XX.CXX.XXX
• TRIAC 41.41XX.DXX.XXX
• DALI 41.41XX.EXX.XXX

ASSEMBLY INSTRUCTIONS

1. Turn off the power.
2. Use the screws (A) and dowels to fix the mounting box and the hanger shafts to the ceiling (mounting holes scheme and the spacing of slings on the other side of the page).
3. Adjust the length of the steel cables and lock them in the hanger body. Then, the cables through the holes in the rollers. Screw the hanger body into the shaft. Cut the excess of the cable.
4. Adjust the length of the wire and lock it with the end stop. You can store the ex in the box or cut off the lamp.
5. Connect the 230V power. Remember to ground (electrical wiring diagrams on the other side of the page).
6. Using a screw (B), screw the lid to the assembly box.
7. Install the diffuser in the luminaire:
   • Half the length of the lamp press the end of the diffuser to profile, and then insert.
   • Press the other end of the diffuser. To pull out, gently pry with a plastic object and push out.
8. Turn on the power.
9. The enclosed tool kit is designed for solid materials (solid brick, wood, concrete, aerated concrete) and gypsum board surfaces. The dowel should be properly matched to the mounting surface. Proper use of the dowel affects the safety and strength of the structure.

TOOLS

References

• Strona główna - Chors

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>