Z-Lite 3038-4RB Easton 4 Bulb Chandelier Instruction Manual
- June 13, 2024
- Z-Lite
Table of Contents
INSTALLATION AND SAFETY INSTRUCTIONS
FOR YOUR SAFETY
WARNING: BE SURE THE ELECTRICITY TO THE WIRES YOU ARE WORKING ON IS SHUT OFF; EITHER THE FUSE IS REMOVED OR THE CIRCUIT BREAKER IS SHUT OFF. GENERAL You don’t need special tools to install this fixture. Be sure to follow the steps in the order given. Under no circumstances should a fixture be hung on house electrical wires, nor should a swag type fixture be installed on a ceiling which contains a radiant type heating system. Read instructions carefully. If you are unclear as to how to proceed, consult a qualified electrician. NOTE: Proper wiring is essential for the safe operation of this fixture.
GENERAL
You don’t need special tools to install this fixture. Be sure to follow the steps in the order given. Under no circumstances should a fixture be hung on house electrical wires, nor should a swag type fixture be installed on a ceiling, which contains a radiant type heating system. Read instructions carefully. If you are unclear as to how to proceed, consult a qualified electrician. NOTE: Proper wiring is essential for the safe operation of this fixture.
FIXTURE ASSEMBLY
Carefully removed the fixture from the carton and check that all parts are included as shown in figure. Be careful not to misplace any of the screws or parts, which are needed to install this fixture.
INSTALLATION
IMPORTANT: Do not attach fixture directly to outlet box.
STEP1: Install universal mounting plate(J) onto the outlet box, and
secure with box screw(I).
STEP2: Put the CUP (D) on the nipple(E).
STEP2: Assemble the rods (F) together, then thread the bottom end of rod
(F) onto the nipple(E) and the swivel(L) onto the top end of rod(F).
Proceed to connect wires:
GROUNDING INSTRUCTIONSSTEP 1: Insert the green grounding screw into the
hole with two raised dimples on the circular strap. Wrap the ground wire from
the fixture (if supplied) around the green grounding screw, then connect it to
ground wire from the outlet box (if not fixed on the outlet box) using a wire
connector (not supplied). If ground wire from the fixture is not supplied,
wrap the ground wire (if not fixed on the outlet box) from the outlet box
around the green grounding screw and tighten it.
| GROUP A: Connect to Black House Wire | GROUP B: Connect to White House Wire |
|---|---|
| BLACK | WHITE |
| *PARALLEL WIRE (round & smooth) | *PARALLEL WIRE (square & ridged) |
| WHITE OR GREY WITH TRACER | WHITE OR GREY WITHOUT TRACER |
| BROWN GOLD OR BLACK WITHOUT TRACER | BROWN, GOLD OR BLACK WITH TRACER |
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES.
STEP 2: Take note of the color of the wire(s) on your fixture.
Identify which group your fixture wire(s) falls into and connect the wires
according to the directions below:
*NOTE: When parallel wire (SPT-I & SPT-2) is used, the tracer wire is
square shaped or ridged and the less tracer wire is round in shape or smooth
(seen best when viewed from wire end.)
STEP 3: Take your fixture wire(s) from group A and place evenly against
the black wire from the outlet box. Do NOT twist wires together before using
wire connectors.
STEP 4: Fit a wire connector (not supplied) over the wires and screw the
connector clockwise until you feel a firmness.
STEP 5: Try gently to pull the connector off the wires. If you can pull
the connector off, carefully re-do steps 3 and 4, as above, and check again
for a firm connection
STEP 6: Connect the fixture wire from group B to the white wire from the
outlet box in the same manner
FINAL ASSEMBLY
STEP1: After wires are connected, tuck them carefully inside outlet box.
STEP2:Put the canopy (G) on the mounting screw (K) and secure them with
the nut (H).
STEP3: Put the Tube (B) on the socket (C).
STEP4:Install the bulb (A) (NO INCLUDED BULB) on the socket (C)
CLEANING
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap. Do not
use abrasive materials such as scouring pads or powders, steel wool or
abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order replacement parts. All parts for this fixture can be ordered from place of purchase. Be sure to use exact wording from illustration when ordering parts.
Line art shown may not exactly match the fixture enclosed.
However, the installations do apply to this fixture.
ITEM NO: 3038-4
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>