Z-Lite 7502-1S Sutton One Light Wall Sconce Instruction Manual
- June 13, 2024
- Z-Lite
Table of Contents
Z-Lite 7502-1S Sutton One Light Wall Sconce
Product Information
The product is a fixture that needs to be installed on an outlet box. It does not require any special tools for installation. Proper wiring is essential for the safe operation of this fixture.
Key Features:
- Universal mounting plate
- Green grounding screw
- Group A and Group B wiring connections
Product Usage Instructions
Installation and Safety Instructions:
WARNING: Before starting the installation, make sure the electricity to
the wires you are working on is shut off. Either remove the fuse or shut off
the circuit breaker.
- Read the instructions carefully and follow the steps in the given order.
- Do not hang the fixture on house electrical wires or install a swag type fixture on a ceiling with a radiant type heating system.
- If unsure about how to proceed, consult a qualified electrician.
Fixture Assembly:
- Carefully remove the fixture from the carton and check that all parts are included.
- Make sure not to misplace any of the screws or parts needed for installation.
Carefully removed the fixture from the carton and check that all parts are included as shown in figure. Be careful not to misplace any of the screws or parts, which are needed to install this fixture.
Grounding Instructions:
STEP 1:
- Insert the green grounding screw into the hole with two raised dimples on the circular strap.
- If the ground wire is supplied with the fixture, wrap it around the green grounding screw and connect it to the ground wire from the outlet box using a wire connector.
- If the ground wire is not supplied with the fixture, wrap the ground wire from the outlet box around the green grounding screw and tighten it.
- Never connect the ground wire to black or white power supply wires.
Wiring Instructions:
STEP 1:
- Identify the color of the wires on your fixture.
- Connect the fixture wires according to the directions below:
| Group A | Group B | House Wire |
|---|---|---|
| Connect to Black | Connect to White | BLACK |
| Connect to White or Grey with White Tracer | Connect to Brown, Gold or Black | |
| without Tracer | WHITE OR GREY WITH WHITE TRACER |
STEP 2:
- Take your fixture wires from Group A and place them evenly against the black wire from the outlet box. Do not twist the wires together before using wire connectors.
- Fit a wire connector over the wires and screw it clockwise until firm.
- Try gently pulling the connector off the wires. If it comes off, redo steps 3 and 4 and check again for a firm connection.
STEP 3:
- Connect the fixture wire from Group B to the white wire from the outlet box in the same manner as Step 2. Make sure no bare wires are visible outside the wire connectors.
Final Assembly:
- STEP 1: After the wires are connected, carefully tuck them inside the outlet box. Assemble the backplate to the universal mounting plate, aligning the mounting holes.
- STEP 2: Tighten the backplate on the universal mounting plate with the mounting screws (A) from the top and the bottom of the backplate, slide the glass (E) over the socket, then secure the retaining ring (G) and metal cover (F) to the Socket with spacer tool (H).
- STEP 3: Install light bulb. (BULB IS NOT INCLUDED, please do not exceed the maximum capacity recommended on the socket.)
Line art shown in the manual may not exactly match the fixture enclosed.
However, the installations do apply to this fixture.
ITEM NO: 7502-1S 7502-2V 7502-3V 7502-4V 7502-5V
FOR YOUR SAFETY WARNING
BE SURE THE ELECTRICITY TO THE WIRES YOU ARE WORKING ON IS SHUT OFF; EITHER
THE FUSE IS REMOVED OR THE CIRCUIT BREAKER IS SHUT OFF.
GENERAL
You don’t need special tools to install this fixture. Be sure to follow the
steps in the order given. Under no circumstances should a fixture be hung on
house electrical wires, nor should a swag type fixture be installed on a
ceiling, which contains a radiant type heating system. Read instructions
carefully. If you are unclear as to how to proceed, consult a qualified
electrician.
NOTE: Proper wiring is essential for the safe operation of this fixture.
INSTALLATION
IMPORTANT: Do not attach fixture directly to outlet box.
STEP 1: Secure universal mounting plate (B) to outlet box with outlet box
screws
GROUNDING INSTRUCTIONS
- STEP 1: Insert the green grounding screw into the hole with two raised dimples on the circular strap. Wrap the ground wire from the fixture (if supplied) around the green grounding screw, then connect it to ground wire from the outlet box (if not fixed on the outlet box) using a wire connector (not supplied). If ground wire from the fixture is not supplied, wrap the ground wire (if not fixed on the outlet box) from the outlet box around the green grounding screw and tighten it.
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES.
- STEP 2: Take note of the color of the wire(s) on your fixture. Identify which group your fixture wire(s) falls into and connect the wires according to the directions below:
GROUP A: Connect to Black House Wire| GROUP B : Connect to W h i t e House
Wire
---|---
BLACK| WHITE
PARALLEL W I R E ( round & smooth)| PARALLEL W I R E ( square & ridged)
WHITE OR GREY WITH TRACER| WHITE OR G R E Y WITHOUT TRACER
BROWN G O L D OR BLACK WITHOUT TRACER| BROWN, GOLD OR BLACK WITH TRACER
NOTE: When parallel wire (SPT-I & SPT-2) is used, the tracer wire is square shaped or ridged and the less tracer wire is round in shape or smooth (seen best when viewed from wire end.)
- STEP 3: Take your fixture wire(s) from group A and place evenly against the black wire from the outlet box. Do NOT twist wires together before using wire connectors.
- STEP 4: Fit a wire connector (not supplied) over the wires and screw the connector clockwise until you feel a firmness.
- STEP 5: Try gently to pull the connector off the wires. If you can pull the connector off, carefully re-do steps 3 and 4, as above, and check again for a firm connection.
- STEP 6: Connect the fixture wire from group B to the white wire from the outlet box in the same manner. Make sure no bare wires can be seen outside wire connectors.
CLEANING
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order replacement parts. All parts for this fixture can be ordered from place of purchase. Be sure to use exact wording from illustration when ordering parts.
Line art shown may not exactly match the fixture enclosed. However, the
installations do apply to this fixture.
ITEM NO: 7502-1S 7502-2V 7502-3V 7502-4V 7502-5V
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>