Z-Lite 1100-1S-CH Neoma Modern Chrome Lamp Sconce Instruction Manual

June 13, 2024
Z-Lite

1100-1SC-CH Neoma Modern
Chrome Lamp Sconce
Instruction Manual

1100-1S-CH Neoma Modern Chrome Lamp Sconce

INSTALLATION AND SAFETY INSTRUCTIONS

FOR YOUR SAFETY WARNING
BE SURE THE ELECTRICITY TO THE WIRES YOU ARE WORKING ON IS SHUT OFF; EITHER THE FUSE IS REMOVED OR THE CIRCUIT BREAKER IS SHUT OFF.

GENERAL

You don’t need special tools to install this fixture. Be sure to follow the steps in the order given. Under no circumstances should affixture be hung on house electrical wires, nor should a swag type fixture be installed on a ceiling, which contains a radiant type heating system. Read instructions carefully. If you are unclear alto how to proceed, consult a qualified electrician.
NOTE: Proper wiring is essential for the safe operation of this fixture.

FIXTURE ASSEMBLY

Carefully removed the fixture from the carton and check that all parts are included as shown in figure. Be careful not to misplace any of the screws or parts, which are needed to install this fixture.

INSTALLATION

IMPORTANT: Do not attach fixture directly to outlet box.
STEP 1: Secure universal mounting plate (B) to outlet box with outlet box screws

GROUNDING INSTRUCTIONS

STEP 1: Insert the green grounding screw into the hole with two raised dimples on the circular strap. Wrap the ground wire from the fixture (if supplied) around the green grounding screw, then connect it to ground wire from the outlet box (if not fixed on the outlet box) using a wire connector (not supplied). If ground wire from the fixture is not supplied, wrap the ground wire (if not fixed on the outlet box) from the outlet box around the green grounding screw and  tighten it.

NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES.
STEP 2: Take note of the color of the wire(s) on your fixture.
Identify which group your fixture wire(s) falls into and connect the wires according to the directions below:

GROUP A: Connect to Black House Wire GROUP B : Connect to White House Wire
BLACK WHITE
*PARALLEL W I R E ( round & smooth) *PARALLEL WIRE ( square & ridged)
WHITE OR GREY WITH TRACER WHITE OR GREY WITH OUT TRACER
BROWN GOLD OR BLACK WITHOUT TRACER BROWN, GOLD OR BLACK WITH TRACER

*NOTE: When parallel wire (SPT-I & SPT-2) is used, the tracer wire is square shaped or ridged and the less tracer wire is round in shape or smooth (seen best when viewed from wire end.)
STEP 3: Take your fixture wire(s) from group A and place evenly against the black wire from the outlet box. Do NOT twist wires together before using wire connectors.
STEP 4: Fit a wire connector (not supplied) over the wires and screw the connector clockwise until you feel a firmness.
STEP 5: Try gently to pull the connector off the wires. If you can pull the connector off, carefully re-do steps 3 and 4, as above, and check again for a firm connection.
STEP 6: Connect the fixture wire from group B to the white wire from the outlet box in the same manner. Make sure no bare wires can be seen outside wire connectors.

FINAL ASSEMBLY

STEP 1: After wires are connected, tuck them carefully inside outlet box. Assemble backplate to the universal mounting plate (B) allowing the mounting holes are align up.
STEP 2: Tighten the backplate on the universal mounting plate with the mounting screws (A) from the top and the bottom of the backplate, slide the glass (E) over the socket, then secure the retaining ring (G) and metal cover (F) to the  Socket with spacer tool (H).
STEP 3: Install light bulb. (BULB IS NOT INCLUDED, please do not exceed the maximum capacity recommended on the socket.)

CLEANING

To clean, wipe fixture with a soft cloth. Clean glass with a mild soap. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

ORDERING PARTS

Keep this sheet for future reference, and in case you need to order replacement parts. All parts for this fixture can be ordered from place of purchase. Be sure to use exact wording from illustration when ordering parts.Z Lite 1100 1S CH Neoma Modern Chrome Lamp Sconce -
lamp

Line art shown may not exactly match the fixture enclosed.
However, the installations do apply to this fixture.
ITEM NO: 1100-1S 1100-2V 1100-3V 1100-4V 1100-5V

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Z-Lite User Manuals

Related Manuals