Minka Lavery 2012-66A-L Vantage 1 Light LED Vanity Light with White Acrylic Shade Instruction Manual

Minka Lavery 2012-66A-L Vantage 1 Light LED Vanity Light with White

Acrylic Shade

Product Information

The product is an indoor light fixture with the model number 2011/2012-66A/84-L. It is a newly released product as of February 9, 2023. The fixture is dimmable and compatible with ELV and/or LED wall dimmer switches. The installation instructions should be followed carefully to ensure proper usage and safety.

Product Usage Instructions

1. Before starting the installation, shut off the power at the fuse box or circuit breaker.
2. Remove the old fixture, including the mounting hardware.
3. Unpack the new fixture and lay out all the parts in a clear area, ensuring that no small parts are misplaced.
4. Loosen screws (C) to remove the mounting plate (A) from the fixture body (D).
5. Attach the mounting plate (A) to the junction box using the provided mounting screws (B) (#8-32N*L0.5). The side of the mounting plate marked GND must face out.
6. Connect the electrical wires as shown in Fig. 2:
   • If your junction box has a ground wire (green or bare copper), connect the fixture’s ground wire to it.
   • If there is no ground wire in the junction box, connect the fixture’s ground wire directly to the mounting plate (A) using the provided green screw.
   • Make sure all wire connectors are securely fastened.
   • Tuck wire connectors neatly into the junction box.
7. Place the fixture body (D) over the mounting plate (A) and secure it with screws (C).
8. To replace the LED module, follow these steps:
   • Shut off the power.
   • Remove screws (C) and the fixture body from the mounting plate (A).
   • Disconnect wire connectors and place the fixture body on a clean surface.
   • Loosen screws (E) and remove the rectangular plate (K) and acrylic shade (J).
   • Press the button labeled L on the quick connector on the LED module (G) with a screwdriver to disconnect the black wire, and then disconnect the white wire labeled N on the quick connector.
   • Loosen screws (H) and carefully remove the LED module (G).
   • Reverse steps b-e to install the new LED module.
9. Once the installation is complete, restore power to the junction box and test the fixture.

Note: The illustration in figure 1 in this manual is for installation purposes only and may not be identical to the purchased fixture.

NSTALLATION INSTRUCTIONS

Item#2011/2012-66A/84-L (New. 2023/02/09)
READ AND SAVE THESE INSTRUCTIONS

WARNING ! SHUT POWER OF FAT FUSE OR CIRCUIT BREAKER .

MOUNTING THE FIXTURE (Fig. 1)

1. Shut off power at the fuse box or circuit breaker box and remove the old fixture including the mounting hardware.
2. Carefully unpack your new fixture and lay out all the parts in a clear area. Take care not to misplace any small parts necessary for installation.
3. Loosening screws (C) to remove mounting plate (A) from fixture body (D).
4. Attach mounting plate (A) to junction box (Not included) using mounting screws (B) (Size: #8-32N*L0.5”). The side of the mounting plate (A) marked “GND” must face out. CONNECTING THE WIRES (Fig. 2)
5. Connect the electrical wires as shown in Fig. 2, making sure that all wire connectors are secured. If your junction box has a ground wire (green or bare copper), connect fixture’s ground wire to it. Otherwise, connect fixture’s ground wire directly to mounting plate (A) using green screw provided.
6. Tuck wire connectors neatly into the junction box. COMPLETING THE INSTALLATION (Fig. 1)
7. Place fixture body (D) over mounting plate (A) and secure with screws (C).

Replacing LED module (Fig. 3)
The LED module can be replaced by a qualified electrician without cutting of wire and without damage to any decorative element to which the fixture is attached. See installation steps for more details (Fig 3.)

1. Shut off the power.
2. Remove screws (C) and fixture body from mounting plate (A).(Fig.1) Disconnect wire connectors and place fixture body on a clean surface.
3. Loosen screws (E) and remove rectangular plate (K) and acrylic shade (J).
4. Press button printed “L” on quick connector on LED module (G) with screwdriver (not included) to disconnect black wire, and then disconnect white wire printed “N” on quick connector on LED module (G).
5. Loosen screws (H), then carefully remove LED module (G).
6. Reverse steps b-e for installing new LED module.

Your installation is now complete. Return power to the junction box and test the fixture.

Note: The illustration in figure 1 on this manual is for installation purposes only. It may or may not be identical to the fixture purchased. Dimmable with ELV and/or LED compatible wall dimmer switches.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>