Minka-Lavery 72792-143-L Shore Pointe Oil Rubbed Bronze Outdoor LED Wall Mount Instruction Manual

Minka-Lavery 72792-143-L Shore Pointe Oil Rubbed Bronze Outdoor LED Wall

Mount

Product Information

The product is Model # 72792-143-L. It is an electrical fixture that requires installation. The fixture includes a mounting plate (Part# A-020), an LED module (Part# L-MD-C1402-11W), a ground screw, and two mounting screws.

Product Usage Instructions

1. Before starting the installation, make sure to shut off the power at the circuit breaker or fuse.
2. Remove the old fixture, including the mounting hardware.
3. Carefully unpack the new fixture and lay out all the parts.
4. Refer to Fig. 1 for the placement of the mounting plate (Part# A-020), LED module (Part# L-MD-C1402-11W), ground screw, and mounting screws.
5. Connect the fixture wires to the house wires:
   • Connect the black fixture wires to the black house wires (hot).
   • Connect the white fixture wires to the white house wires (neutral).
   • Connect the green or bare copper fixture wires to the green or bare copper house wires (ground).
6. Refer to Fig. 2 for visual guidance on connecting the wires.
7. Securely mount the fixture using the provided mounting screws.
8. Refer to Fig. 3 for the correct wire connections.
9. If required, apply caulking around the backplate (Fig. 4) for additional protection.
10. Once the installation is complete, restore power to the outlet box.
11. Test the fixture to ensure it is functioning properly.

For any concerns or if you are unsure about the installation process, it is recommended to consult a qualified electrician to ensure correct branch circuit conductor installation and reduce the risk of fire.

INSTALLATION INSTRUCTIONS

Model # 72792-143-L
READ AND SAVE THESE INSTRUCTIONS

WARNING SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER

PREPARING FOR INSTALLATION (Fig. 1)

1. Shut off power at the circuit breaker and remove the old fixture including the mounting hardware.

2. Carefully unpack your new fixture and lay out all the parts in a clear area. Take care not to misplace any small parts necessary for installation.

3. Thread two screws (C) into the pre-drilled holes in the mounting plate (B) spaced the same distance apart as the holes in the back plate and then secure with nuts. The length of screws (C) into mounting plate (B) may be adjusted if necessary.

4. Attach mounting plate (B) using outlet box screws (F) to outlet box (A) (not supplied). The side of the mounting plate marked “GND” must face out (Fig 1).
   CONNECTING THE WIRES (Fig. 2)

5. Connect the electrical wires as shown in Fig.2. Making sure that all wire connectors are secured. If your outlet box has a ground wire (green or bare copper), connect the fixture’s ground wire to it.
   Otherwise, connect the fixture’s ground wire directly to the mounting plate using the green screw (D) provided.
   FINISHING THE INSTALLATION (Fig. 1)

6. Slide the back plate over screws (C) and secure with cap nuts (H) (Fig 1).

7. To prevent moisture from entering the outlet box (A) (not supplied) and causing a short, use clear silicone sealant to outline the outside of fixture back plate where it meets the wall leaving a space at bottom to allow moisture a means to escape (Fig. 3)

8. LED information (1 x AC LED 11W included.) (DO NOT EXCEED THE MAXIMUM WATTAGE RATING) (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!)

Replacing LED

Replacing LED module (Fig.4)
The LED module can be replaced by a qualified electrician without cutting of wire and without damage to any decorative element to which the fixture is attached. See installation steps for more details (Fig.4).

• Shut off power. Remove Glass (R), loosen screws (I) and plastic washer (P), then remove glass panel (J).
• Loosen screws (Q) and rubber washer (K) on the LED module.
• Loosen screws (M) and separate the top cover (O) from the fixture frame (N), then disconnect the plug on the wires. Carefully remove LED module (L).
• Reverse steps a-c for installing the new LED module.

Note: The LED module should be provided by a specified supplier.
Your installation is now complete. Return power to the outlet box and test the fixture.

CAUTION-RISK OF FIR E CONSULT A QU ALIFIED ELECTRICIAN TO ENSURE CO RRECT BRANCH CIRCUIT CONDUCTOR”

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>