Minka-Lavery 73330-66A 2 Light Black Outdoor Wall Mount Instruction Manual

Minka-Lavery 73330-66A 2 Light Black Outdoor Wall Mount

Product Information

• Product Name: Item#73330-66A
• Installation Date: 2023/02/16
• Manufacturer: Unknown

Installation Instructions WARNING! Before starting the installation process, shut off the power at the fuse or circuit breaker.

Mounting the Fixture (Fig.1)

1. Shut off the power at the circuit breaker and remove the old fixture, including the mounting hardware.
2. Carefully unpack your new fixture and lay out all the parts on a flat surface.
   • Mounting Plate
   • Ground Screw
   • Mounting Screw *2

Connecting the Wires (Fig. 2)

7. Connect the electrical wires as shown in Fig. 2.
   • Fixture Wires: Black or Smooth
   • Fixture Wires: White or Ribbed
   • Fixture Wires: Green or Bare Copper (Ground)
   • House Wires: Black (Hot)
   • House Wires: White (Neutral)
   • House Wires: Green (Ground)
8. Tuck wire connectors neatly into the junction box.

Completing the Installation (Fig.1)

9. Align fixture body onto mounting plate and secure with plastic washer and screws.
10. To prevent moisture from entering the outlet box and causing damage, apply caulk around the edges of the fixture (optional).

Your installation is now complete. Restore power and test the fixture.

Note: The illustration shown in Fig. 1 is for installation purposes only and may or may not be identical to the fixture purchased.

INSTALLATION INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.

MOUNTING THE FIXTURE

(Fig.1)

1.  Shut off the power at the circuit breaker and remove the old fixture, including the mounting hardware.
2. Carefully unpack your new fixture and lay out all the parts on a clear area. Take care not to lose any small parts necessary for installation.
3. Pull up latch (H) and open the door. Install glass Panels (K)(1pc, Size: L460mm x W132mm), (J) (2pcs, Size: L460mm x W108mm), (L) (1pc, Size: L437mm x W109mm) onto fixture body (C) and secure with tabs inside frame.
4. Position mounting plate (A) on wall and mark location of the two mounting holes. Pre-drill the holes for dry wall anchors (N). Insert drywall anchors (N) into wall.
5. Attach mounting plate (A) to junction box using mounting screws (B) (Size: #8-32N*L0.5”). The side of mounting plate marked “GND” must face out.
6. Secure mounting plate (A) by inserting wood screws (M) through holes on mounting plate into the plastic anchors (N).

CONNECTING THE WIRES

(Fig. 2)

7. Connect the electrical wires as shown in (Fig. 2). Making sure that all wire connectors are secured. If your outlet box has a ground wire (green or bare copper), connect fixture’s ground wire to it. Otherwise, connect fixture’s ground wire directly to mounting plate (A) using green screw provided.
8. Tuck wire connectors neatly into the junction box.

COMPLETING THE INSTALLATION

(Fig.1)

9. Align fixture body (C) onto mounting plate (A) and secure with plastic washer (E) and screws (D).
10. To prevent moisture from entering the outlet box and causing a short, use clear caulking (i.e. Indoor/Outdoor Silicone Sealant) to outline outside of fixture back-plate where it meets the wall leaving a space at bottom to allow moisture a means to escape (Fig.3).
11. Place candle covers (F) over sockets (I).
12. Install (2) two candelabra base bulbs (G) up to 60 watts or CFL or LED equivalent (not included) in accordance with the fixture specification. (DO NOT EXCEED THE SPECIFIED WATTAGE!) (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!).
13. Close the door and re-latch (H) onto door.

Your installation is now complete. Return power and test the fixture.

Note : Illustration (Fig. 1) on this manual is for installation purposes only. It may or may not be identical to the fixture purchased.

LA-3622E

Item#73330-66A (New. 2023/02/16)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>