FORTIN Nissan Micra 2015 Standard-Key Remote Starters and Alarm Systems Installation Guide

June 13, 2024
FORTIN

FORTIN Nissan Micra 2015 Standard-Key Remote Starters and Alarm Systems Installation Guide
Remote Starters and Alarm Systems

REGULAR INSTALLATION

ADDENDUM – SUGGESTED WIRING CONFIGURATION

Vehicle functions supported in this diagram (functional if equipped)

VEHICLE| YEARS
Micra| Immobilizer bypass
.| Lock
.| Arm
.| Unlock
.| Disarm
.| Parking Lights
.| Tachometer
.| Door Status
.| Trunk Status
.| Hood Status
.| Hand-Brake Status
.| Foot-Brake Status
| FIRMWARE VERSION
72.[43]
MINIMUM| To add the firmware version and the options, use the FLASH LINK UPDATER or FLASH LINK MOBILE tool, sold separately.
---|---|---
| Program bypass option IF THE VEHICLE IS NOT EQUIPPED WITH FUNCTIONAL HOOD PIN| UNIT OPTION| DESCRIPTION
---|---|---|---
A11
| Hood trigger (Output Status)

Parts required (Not included)
1X Fusible

MANDATORY INSTALL

**HOOD PIN

HOOD STATUS : THE HOOD PIN SWITCH MUST BE INSTALLED IF THE VEHICLE CAN BE REMOTE STARTED WITH THE HOOD OPEN, SET FUNCTION A11 TO OFF
A11

Notice:** the installation of safety elements are mandatory. The hood pin is an essential security element and must be installed.

THIS MODULE MUST BE INSTALLED BY A QUALIFIED TECHNICIAN. A WRONG CONNECTION CAN CAUSE PERMANENT DAMAGE TO THE VEHICLE.

This guide may change without notice. Seewww.fortin.ca for latest version

DESCRIPTION

Connection Instruction

  1. Ignition harness
  2. Transponder connector
  3. Driver kick panel
  4. OBDII’
  5. BCM

WIRING CONNECTION

Connection Instruction

  1. Ignition harness White connector – Back view

  2. Transponder connector White connector – Back view

  3. Driver kick panel – Grey connector – Back view

  4. OBDII Front view

  5. BCM White connector –

  6. Back vue. 15-pin Black connector at BCM.
    For Autolight shut down
    Parts Instruction

KEY BYPASS PROGRAMMING PROCEDURE 1/2

  1. Press and hold the programming button: Connect the 4-PIN Data-link harness (Black connector).
    The Blue, Red, Yellow and Blue & Red LEDs will alternatively illuminate

  2. Release the programming button when the LED is YELLOW.
    If the LED is not solid YELLOW disconnect the 4-Pin connector (Main-Hamess) and go back to step 1.
    Product Using Instruction

  3. Insert the required remaining connectors.
    Product Using Instruction

  4. Press and release the programming button two times (2x)
    The YELLOW LED will alternate between 2x flashes and a pause.
    Wait until the YELLOW LED turns ON.
    Product Using Instruction

  5. Turn the key to the Ignition ON/RUN position.
    The RED LED will turns ON.
    Product Using Instruction
    If the YELLOW and RED LED’s are not solid, remove the key and go back to step

  6. Repeat this step until the RED and YELLOW LED’s are solid
    Product Using Instruction
    Wait for the BLUE LED to flash rapidly
    Product Using Instruction

  7. Turn the key to the OFF position

  8. Remove the key from the Ignition barrel.

  9. Turn the key to the Ignition ON/RUN position.
    The BLUE, YELLOW and RED LED’s will rapidly alterate
    Product Using Instruction

  10. When the YELLOW LED begins to flash rapidly: Key bypass programmed

The module is now programmed
Use the remote of the remote starter or security system to test all of the supported features to ensure proper programming.

Module label
Module label
Notice:
Updated Firmware and Installation Guides Updated fi rmware and installation guides are posted on our web site on a regular basis. We recommend that you update this module to the latest firmware and download the latest installation guide(s) prior to the installation of this product.

WARNING
The information on this sheet is provided on an (as is) basis with no representation or warranty of accuracy whatsoever. It is the sole responsibility of the installer to check and verify any circuit before connecting to it. Only a computer safe logic probe or digital multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or responsibility whatsoever pertaining to the accuracy or currency of the information supplied. The installation in every case is the sole responsibility of the installer performing the work and FORTIN ELECTRONIC SYSTEMS assumes no liability or responsibility whatsoever resulting from any type of installation, whether performed properly, improperly or any other way. Neither the manufacturer or distributor of this module is responsible of damages of any kind indirectly or directly caused by this module, except for the replacement of this module in case of manufacturing defects. This module must be installed by qualified technician. The information supplied is a guide only. This instruction guide may change without notice. Visit www.fortinbypass.com to get the latest version.

Contact IconTECH SUPPORT
Tél: 514-255-HELP (4357)
1-877-336-7797
ADDENDUM GUIDE

WEB UPDATE
www.fortinbypass.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

FORTIN User Manuals

Related Manuals