FORTIN THAR-VW1 Harness Allows You To Connect Installation Guide

 THAR-VW1 Harness Allows You To Connect

VEHICLE……….. YEARS
ADDENDUM – SUGGESTED WIRING CONFIGURATION
THAR-VW1 INSTALLATION

Vehicle functions supported in this diagram (functional if equipped)

VOLKSWAGEN

Golf MFD……………. 01-2014 to 08-2014

COMPATIBLE MODULE
REQUIRED:| QR CODE ON THE LABEL
MANUFACTURED AFTER: 2019| FIRMWARE VERSION
| To add the firmware version and the options, use the
FLASH LINK UPDATER or FLASH LINK MOBILE tool,
sold separately.
---|---|---|---

Golf MFD ………………….09-2014 & +

COMPATIBLE MODULE
REQUIRED:| QR CODE ON THE LABEL MANUFACTURED AFTER: 2019| FIRMWARE VERSION| To add the firmware version and the options, use the FLASH LINK UPDATER or FLASH LINK MOBILE tool, sold separately.
---|---|---|---

NOTES

Vehicle’s equipped with Virtual Cluster, not supported for the key bypass.

MANDATORY INSTALL

• HOOD PIN CONTACT DE CAPOT HOOD STATUS : THE HOOD PIN SWITCH (INCLUDED) MUST BE INSTALLED IF THE VEHICLE CAN BE REMOTE STARTED WITH THE HOOD OPEN, SET FUNCTION A11 TO OFF. SECURITY STICKER
  ** WARNING ATTENTION
  Included Inclus
  Notice: the installation of safety elements are mandatory. The hood pin and the sticker are essential security elements and must be installed.
  THIS MODULE MUST BE INSTALLED BY A QUALIFIED TECHNICIAN. A WRONG CONNECTION CAN CAUSE PERMANENT DAMAGE TO THE VEHICLE.
  NOTES**

Program bypass option:

Program bypass option (If equiped with OEM alarm):

Program remote starter option for Diesel vehicules:| FUNCTION| MODE| DESCRIPTION
---|---|---|---
18| 3| Enable (10 seconds) delay between Ignition power up and Starter
(crank)
| 32| 6| Bypass control
for R.S. OEM REMOTE STAND ALONE:| 38| 5| Enable (Press Lock, Unlock and Lock to remote start)
for COMFORT GROUP ACTIVATION:| 39| 2| Temperature option : AUX.1 activated at 5o C, 5 seconds after remote started
| Parts required (Not included)
---|---
| PROGRAMMING TOOL REQUIRED for key bypass programming. Sold separately.
| 1x TB-VW (key bypass)

DESCRIPTION

AUTOMATIC TRANSMISSION WIRING CONNECTION

MANUAL TRANSMISSION WIRING CONNECTION

DCRYPTOR PROGRAMMING PROCEDURE

Parts required (not included)
FLASH LINK UPDATER,
FLASH LINK MANAGER
SOFTWARE | PROGRAMME
Microsoft Windows Computer with Internet connection
OR
FLASH LINK MOBILE
FLASH LINK MOBILE APP
Smartphone Android or iOS with Internet connection (Internet provider charges may apply)
BEFORE PROGRAMMING SET THE UNIT OPTIONS AND SAVE.

| Take out the battery from the remote control.
---|---
| Place the transponder’s ring in front of the remote control.
| With the remote beside the antenna ring, proceed with the programming on the next pages.
| Connect the R-LINK instead of the TB-VW.
| WARNING:
Close and open the driver door.

KEY BYPASS PROGRAMMING PROCEDURE 2/4

| Press and hold the programming button:
Connect the 4-PIN Data-link harness (Black connector).
---|---
| Release the programming button when the BLUE LED is ON. If the LED is not solid BLUE disconnect the 4-PIN Data-link harness (Black connector).
| Insert the required  remaining connectors.
| Press the Push-to-Start button to turn ON the ignition.
| Press and release the programming button once (1x).
The BLUE LED will turn off.
Wait,
The BLUE LED will flash rapidly.
| Press and hold the programming button.
The BLUE LED will turn OFF.
Wait,
The RED LED will turn ON.
Release the programming button.

KEY BYPASS PROGRAMMING PROCEDURE 3/4

| Wait, do not touch the vehicle or the module.
The BLUE, RED and YELLOW LEDs will rapidly alternate.
the RED LED to turn ON.
Wait,
the YELLOW LED will flash once.
---|---
| Wait,
Wait for the RED and YELLOW LEDs to slowly alternate.
If the RED LED flashes slowly, the programming has failed, go back to step1 and start the programming over.
| Press the Push-to-Start button once to turn off the ignition.
| Disconnect all connectors and after the 6-Pin (Main-Harness) or the 4-Pin Data-link connector.
| Use the tool:
FLASH LINK UPDATER or FLASH LINK MOBILE to visit the DCryptor menu.
*Parts required (not included)
| AFTER DCRYPTOR PROGRAMMING COMPLETED
Go back to the vehicle and reconnect the 6-Pin (MainHarness) or the 4-pins (Data-Link) connector and after all the remaining connector.

KEY BYPASS PROGRAMMING PROCEDURE 4/4

NOTE
IF PROGRAMMING IS INTERRUPTED DURING THE PROCESS, SUCH AS A MODULE IS DISCONNECTED OR BY TURNING OFF THE IGNITION WITH THE KEY, IT IS POSSIBLE THAT THE VEHICLE WILL NO LONGER START NORMALLY, YOU MUST DISCONNECT AND RECONNECT THE VEHICLE BATTERY TO CORRECT THE SITUATION.

| Take out the remote control from the transponder’s ring.
---|---
| Insert the battery into the remote control.
| Connect the TB-VW instead of the R-LINK.
| The module is now programmed.
| REMOTE STARTER / ALARM VERIFICATION PROCEDURE
TTest the remote starter. Remote start the vehicle.

REMOTE STARTER PROGRAMMING PROCEDURE

REFER TO THE QUICK INSTALL GUIDE INCLUDED WITH THE MODULE FOR THE REMOTE STARTER PROGRAMMING.

REMOTE STARTER FUNCTIONALITY

| All doors must be closed.
---|---
| Remote start the vehicle.
| Unlock the doors with either:
• The OEM remote
• The remote-starter remote.
| Enter the vehicle with the Intelligent SmartKey.
| The vehicle can now be put in to gear and driven.

Notice: Updated Firmware and Installation Guides
Updated fi rmware and installation guides are posted on our web site on a regular basis. We recommend that you update this module to the latest fi rmware and download the latest installation guide(s) prior to the installation of this product.
WARNING
The information on this sheet is provided on an (as is) basis with no representation or warranty of accuracy whatsoever. It is the sole responsibility of the installer to check and verify any circuit before connecting to it. Only a computer safe logic probe or digital multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or responsibility whatsoever pertaining to the accuracy or currency of the information supplied. The installation in every case is the sole responsibility of the installer performing the work and FORTIN ELECTRONIC SYSTEMS assumes no liability or responsibility whatsoever resulting from any type of installation, whether performed properly, improperly or any other way. Neither the manufacturer or distributor of this module is responsible of damages of any kind indirectly or directly caused by this module, except for the replacement of this module in case of manufacturing defects. This module must be installed by qualifi ed technician. The information supplied is a guide only. This instruction guide may change without notice. Visit www.fortinbypass.com to get the latest version.

Copyright © 2006-2019, FORTIN AUTO RADIO INC
ALL RIGHTS RESERVED PATENT PENDING
TECH SUPPORT
Tél: 514-255-HELP (4357)
1-877-336-7797
ADDENDUM GUIDE
www.fortinbypass.com
WEB UPDATE
This guide may change without notice.
See www.fortin.ca for latest version.
REV.: 20211020
Guide # 103001

References

• Over

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>