MINKA LAVERY 7577390 60W 5-Light Candelabra E-12 Semi Flush Mount Ceiling Fixture Installation Guide
- June 13, 2024
- MINKA LAVERY
Table of Contents
MINKA LAVERY 7577390 60W 5-Light Candelabra E-12 Semi Flush Mount Ceiling
Fixture
INSTALLATION INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
**Pendant New
**
HANGING THE FIXTURE (Fig. 1)
-
Carefully remove the fixture from the carton and check that all parts are included as shown in the illustration.
-
Shut off power at the circuit breaker and remove old fixture including the mounting hardware.
-
Determine the desired hanging height and thread rods (G ,H,) to the nipple of the fixture body(K). Then attach loop (L) by screwing in to rod (G).
-
Attach the quick link to loop (L) on the canopy (E), carefully feed the wire over loop (L) and the canopy(E)
-
The mounting bracket (B) contains several pairs of threaded holes, find the pair of holes that match the spacing of the holes in your Junction box(J) Attach the mounting bracket (B) to the Junction Box(J) using the two mounting screws( size:8/32* 25mm). Tighten the screws (C) securely with screwdriver. The side of the mounting plate marked “GND” must face out.
CONNECTING THE WIRES (Fig. 2) -
At this point, connect the electrical wires as shown in (Fig.2), Make sure that all wire connections are secured. If your outlet has a ground wire (green or bare copper), connect the fixtures Ground Wire to it. Otherwise, connect the fixture Ground Wire directly to the circular strap using the Green Screw provided
-
Position the canopy (E) so that the mounting screws(D) protruding from mounting bracket line up with the holes in the canopy. Secure canopy in place with provided mounting screws (F)
INSTALL LIGHT BULB (Fig. 1) -
Install light bulb (T) (excluded) in accordance with the fixture’s specifications. (DO NOT EXCEED THE MAXIMUM WATTAGE RATING!!) (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!) FINISH THE INSTALLATION (Fig. 1)
-
Your installation is complete now. Return power to the junction box and test the fixture. Note: Illustration (Fig.1) on this manual is for installation purposes only. It may or may not be identical to the fixture purchased.
Semi-flush
READ AND SAVE THESE INSTRUCTIONS
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
HANGING THE FIXTURE (Fig. 1)
-
Carefully remove the fixture from the carton and check that all parts are included as shown in the illustration.
-
Shut off power at the circuit breaker and remove old fixture including the mounting hardware.
-
Thread rod (G1) to the nipple of the fixture body (H), and secure the canopy(E) to the rod(G1), carefully feed the wire over the canopy(E).
-
The mounting bracket (B) contains several pairs of threaded holes, find the pair of holes that match the spacing of the holes in your Junction box(J) Attach the mounting bracket (B) to the Junction Box(J) using the two mounting screws size:8/32* 25mm). Tighten the screws (C) securely with screwdriver. The side of the mounting plate marked “GND” must face out
CONNECTING THE WIRES (Fig. 2) -
At this point, connect the electrical wires as shown in (Fig.2), Make sure that all wire connections are secured. If your outlet has a ground wire (green or bare copper), connect the fixtures Ground Wire to it. Otherwise, connect the fixture Ground Wire directly to the circular strap using the Green Screw provided.
-
Position the canopy (E) so that the mounting screws(D) protruding from the mounting bracket line up with the holes in the canop. Secure canopy in place with provided mounting screws (F)
INSTALL LIGHT BULB (Fig. 1) -
Install light bulb (I) (excluded) in accordance with the fixture’s specifications. (DO NOT EXCEED THE MAXIMUM WATTAGE RATING!!) (NE PASDEPASSER LA PUISSANCE NOMINALE MAXIMALE!)
FINISH THE INSTALLATION (Fig. 1) -
Your installation is complete now. Return power to the junction box and test the fixture. Note: Illustration (Fig.1) on this manual is for installation purposes only. It may or may not be identical to the fixture purchased.