FORTIN 79931 Ford GT 2008 Standard-Key Remote Starters and Alarm Systems Instruction Manual

79931 Ford GT 2008 Standard-Key Remote Starters and Alarm Systems
Instruction Manual

79931 Ford GT 2008 Standard-Key Remote Starters and Alarm Systems

ADDENDUM – SUGGESTED WIRING CONFIGURATION Vehicle functions supported in this diagram (functional if equipped)
Immobilizer bypass

• Lock
• Unlock
• Arm
• Disarm
• Parking Light
• Horn
• Hood Status*
• Foot-Brake Status

FIRMWARE VERSION VERSION LOGICIELLE 71.[52] MINIMUM
To add the firmware version and the options, use the FLASH LINK UPDATER or FLASH LINK MOBILE tool, sold separately.
MANDATORY INSTALL
* HOOD PIN CONTACT HOOD STATUS : THE HOOD PIN SWITCH MUST BE INSTALLED IF THE VEHICLE CAN BE REMOTE STARTED WITH THE HOOD OPEN.
Notice: the installation of safety elements are mandatory. The hood pin is an essential security element and must be installed.
THIS MODULE MUST BE INSTALLED BY A  QUALIFIED TECHNICIAN. A WRONG  CONNECTION CAN CAUSE PERMANENT DAMAGE TO THE VEHICLE.

AUTOMATIC TRANSMISSION WIRING CONNECTION

PROGRAM.1: 2 KEY PROGRAMMING PROCEDURE 1/2
2 KEY REQUIRED Press and hold the programming button:
Connect the 4-PIN Data-link harness (Black connector). The Blue, Red, Yellow and Blue & Red LEDs will alternatively illuminate.Release the programming button when the LED is RED.
If the LED is not solid RED disconnect the 4 Pin connector (Data-Link) and go back to step 1.Insert the required remaining connectors.Turn the first functional key to the Ignition ON/RUN  position. Wait 3 seconds.Turn the key to the OFF position.
Remove the first key.Turn the second functional key to the Ignition ON/RUN position.
Wait 3 seconds.
PROGRAM.1: 2 KEY PROGRAMMING PROCEDURE 2/2 | Turn the key to the OFF position. Remove the second key.
CAUTION The following step must be completed within 5 seconds. Otherwise disconnect all connectors and go back to step 1.Press and hold the programming button until the LED flashes once.  The RED LED will flash once (1x). Release the programming button.
AUTOMATIC TRANSMISSIONS Activate the remote starter.
MANUAL TRANSMISSION
Using a jumper wire, apply power (12v) to the vehicle’s ignition1.The RED LED will flash rapidly ten (10) times. If the LED is solid RED disconnect the 4 Pin connector (Data-Link) and go back to step 1. Manual transmission: Remove the jumper.
The module is now programmed.
Use the remote of the remote starter or security system to test all of the supported features to ensure proper programming.

DCRYPTOR PROGRAMMING PROCEDURE

BEFORE PROGRAMMING SET THE UNIT OPTIONS AND SAVE. Press and hold the Insert programming button: the 4-Pin (Data-Link) connector.
The Blue, Yellow, Red and Blue & Red LEDs will alternatively illuminate.Release the programming button when the LED is RED.
If the LED is not solid RED disconnect the 4-Pin connector (Data-Link) and go back to step 1.Insert the required remaining connectors.Press and release the programming button once (1x).

• The RED LED will flash once.

Turn the key to the Ignition ON/RUN position.

• The RED LED will turn OFF.
•  The YELLOW LED will turn on.

KEY BYPASS PROGRAMMING PROCEDURE 2/3 Turn the key to the OFF position Remove the key from the ignition barrel.

• The YELLOW LED will turn OFF.
• The RED LED will turn on.

Turn the key to the Ignition ON/RUN position.

• The RED LED will turn OFF.
•  The YELLOW LED will turn on.

Turn the key to the OFF position Remove the key from the ignition barrel.

• The YELLOW LED will turn OFF.
• The RED LED will turn on.

Turn the key to the Ignition ON/RUN position.

• The YELLOW LED will turn on and off.
• The RED LED will turn OFF.

Turn the key to the OFF position Remove the key from the ignition barrel.

• The RED and YELLOW LEDs will alternate.

KEY BYPASS PROGRAMMING PROCEDURE 3/3 Disconnect all the connectors and after the Data-Link (4-pins) connector. Microsoft Windows Computer with Internet connection
Use the tool: FLASH LINK UPDATER or FLASH LINK MOBILE to visit the Cryptor menu.
Parts required (not included)Smartphone* (Internet provider charges may apply)AFTER DCRYPTOR PROGRAMMING COMPLETED Go back to the vehicle and reconnect the 4-Pin (Data-Link) connector and after, all the remaining connector.
**** The module is now programmed.
REMOTE STARTER / ALARM VERIFICATION
Test the remote starter.

REMOTE STARTER FUNCTIONALITY

All doors must be closed.| Remote start the vehicle.| Unlock the doors with the remote-starter
remote or the OEM remote.

Insert and Turn the key to the
Ignition ON/RUN position.| Press the brake pedal.| The vehicle can now be put in to
gear and driven.

Notice: Updated Firmware and Installation Guides Updated firmware and installation guides are posted on our web site on a regular basis. We recommend that you update this module to the latest fi rmware and download the latest installation guide(s) prior to the installation of this product.
WARNING
The information on this sheet is provided on an (as is) basis with no representation or warranty of accuracy whatsoever. It is the sole responsibility of the installer to check and verify any circuit before connecting to it. Only a computer safe logic probe or digital multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or responsibility whatsoever pertaining to the accuracy or currency of the information supplied. The installation in every case is the sole responsibility of the installer performing the work and FORTIN ELECTRONIC SYSTEMS assumes no liability or responsibility whatsoever resulting from any type of installation, whether performed properly, improperly or any other way. Neither the manufacturer or distributor of this module is responsible of damages of any kind indirectly or directly caused by this module, except for the replacement of this module in case of manufacturing defects. This module must be installed by qualifi ed technician. The information supplied is a guide only. This instruction guide may change without notice. Visit www.fortinbypass.com to get the latest version.

HARDWARE VERSION
FIRMWARE VERSION
Date: xx-xx
INTERFACE MODULE
PATENTS PENDING US: 2007-228827-A1
Made in Canada
www.fortinbypass.com
EVO-ALL TECH SUPPORT
Tél: 514-255-HELP (4357)
1-877-336-7797
ADDENDUM GUIDE
www.fortinbypass.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>