FORTIN 86001 Ford GT 2008 Standard Key Remote Starters and Alarm Systems Instruction Manual

FORTIN 86001 Ford GT 2008 Standard Key Remote Starters and Alarm Systems

Product Information:

This user manual is for the Transponder Bypass product designed for Ford GT vehicles from 2005-2008. It provides information on the firmware version and options, which can be added using the FLASH LINK UPDATER or FLASH LINK MOBILE tool (sold separately). The manual also mentions the required parts, such as a fusee.

Product Usage Instructions

1. To add the firmware version and options, you need to use the FLASH LINK UPDATER or FLASH LINK MOBILE tool. Connect the tool to your computer or smartphone with an internet connection.
2. If using a computer, make sure it is a Microsoft Windows computer with an internet connection. If using a smartphone, ensure it is an Android or iOS device with an internet connection.
3. Reconnect the 4-Pin (Data-Link) connector and then connect all the remaining connectors.
4. Use the FLASH LINK UPDATER or FLASH LINK MOBILE tool to visit the DCryptor menu for further configuration.
5. It is recommended to regularly check for updated firmware and installation guides on the manufacturer’s website before installing the product.

Note: The product is made in Canada and the manufacturer’s website is www.fortinbypass.com. For any further assistance, refer to the service number provided in the manual.

REGULAR INSTALLATION

To add the firmware version and the options, use the FLASH LINK UPDATER or FLASH LINK MOBILE tool,sold separately.

Parts required

(Not included)

• 1X Fus

WIRING CONNECTION

DCRYPTOR PROGRAMMING PROCEDURE

Parts required (not included)

BEFORE PROGRAMMING SET THE UNIT OPTIONS AND SAVE.

Make sure to have one valide vehicle key.

1. If the vehicle equipped with SMART KEY:
   Remove the valet key from the back of the OEM remote.

2. Keep all OEM remotes at least 3 meters (10 feet) away from the vehicle to proceed.

REMOTE STARTER / ALARM VERIFICATION PROCEDURE

• Adjust the remote-carstarters tachometer setting (if required).
• Test the remote-carstarter and keylessentry functionality
• Place the key in front the ignition barrel.
• The remote starter must be able to start the vehicle.

The remote starter must be able to start the vehicle.

1. Press and hold the programming button:
   Insert the 4-Pin (Data-link Connector connector.

2. Release the programming button when the LED is RED.
   If the LED is not solid RED disconnect the 4-Pin connector (Data-Link) and go back to step 1.

3. Insert the required remaining connectors.

4. Press and release the programming button once (1x).
   The RED LED will flash once.

5. Turn the Ignition to the ON/RUN position.
   WAIT the RED LED will turn OFF.
   The YELLOW LED will turn on.

6. Turn the Ignition to the OFF position.
   WAIT the YELLOW LED will turn OFF.
   Lathe RED LED will turn ON.

7. Turn the Ignition to the ON/RUN position.
   The RED and YELLOW LEDs will alternate.

8. Turn the Ignition to the OFF position.

9. Disconnect all connectors.

10. Use the tool:
    FLASH LINK UPDATER or FLASH LINK MOBILE to visit the DCryptor menu.
    Parts required (not included)

11. Reconnect the 4-Pin (Data-Link) connector and after, all the remaining connector.

The module is now programmed

REMOTE STARTER

Test the remote starter

Notice: Updated Firmware and Installation Guides
Updated fi rmware and installation guides are posted on our web site on a regular basis. We recommend that you update this module to the latest fi rmware and download the latest installation guide(s) prior to the installation of this product.

WARNING
The information on this sheet is provided on an (as is) basis with no representation or warranty of accuracy whatsoever.
It is the sole responsibility of the installer to check and verify any circuit before connecting to it. Only a computer safe logic probe or digital multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or responsibility whatsoever pertaining to the accuracy or currency of the information supplied. The installation in every case is the sole responsibility of the installer performing the work and FORTIN ELECTRONIC SYSTEMS assumes no liability or responsibility whatsoever resulting from any type of installation, whether performed properly, improperly or any other way. Neither the manufacturer or distributor of this module is responsible of damages of any kind indirectly or directly caused by this module, except for the replacement of this module in case of manufacturing defects. This module must be installed by qualifi ed technician. The information supplied is a guide only. This instruction guide may change without notice. Visit www.fortinbypass.com to get the latest version.

TECH SUPPORT
Tél: 514-255-HELP (4357)
1-877-336-7797

www.fortinbypass.com

WEB UPDATE

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>