FORTIN 2004 Ford Thunderbird Regular Key Remote Starters and Alarm Systems Installation Guide

FORTIN 2004 Ford Thunderbird Regular Key Remote Starters and Alarm

Systems

Product Information

• Product Name: Thunderbird
• Model Year: 2002-2005
• Bypass Firmware Version: 71.[52]
• Minimum Firmware Version Requirement: To add the firmware version and options, use the FLASH LINK UPDATER or FLASH LINK MOBILE tool (sold separately).
• Program Bypass Option: If the vehicle is not equipped with a functional hood pin, set the UNIT OPTION to A11 (OFF).
• Program Remote Starter Option: Set the FUNCTION to 2.
• Parts Required (Not included): 1x Relay and 1x 1780K Ohm resistor.
• Mandatory Installation: The hood pin switch (included) must be installed if the vehicle can be remote started with the hood open. Set FUNCTION A11 to OFF.
• Security Sticker: Included. This module must be installed by a qualified technician. A wrong connection can cause permanent damage to the vehicle.

Product Usage Instructions

1. Wiring Connections:
   • Yellow: Connect to AA11 (-)Lock
   • Purple: Connect to AA22 (-)Unlock
   • Purple/White: Connect to AA33
   • Green: Connect to AA44
   • White: Connect to AA55
   • Orange: Connect to AA66
   • Orange/Black: Connect to AA77
   • Dk.Blue: Connect to AA88
   • Red/Blue: Connect to AA99 In
   • Lt.Blue/Black: Connect to AA1100 RX In/Out
   • Black: Connect to AA1111 (+)Foot Brake
   • Pink: Connect to AA1122 Out
   • Yellow/Black: Connect to AA1133 (-)Trunk Release
   • Brown/White: Connect to AA1144 In
   • Pink/Black: Connect to AA1155 (-)Hood
   • Purple/Yellow: Connect to AA1166 In/Out
   • Green/White: Connect to AA1177 In/Out
   • Green/Red: Connect to AA1188 In/Out
   • White/Black: Connect to AA1199 Out
   • Lt.Blue: Connect to AA2200 In/Out
   • White Out: Connect to EE11
   • Orange Out: Connect to EE22
   • Red In: Connect to EE33
   • Black In: Connect to EE44
   • Pink In/Out: Connect to EE55
   • Yellow Out: Connect to EE66
2. Cut Loop for Automatic Transmission Mode.
3. Hood Pin Mandatory. Connect the following:
   • C5: Brown
   • C4: Gray/Black
   • C3: Gray
   • C2: Orange/Brown
   • C1: Orange/Green
4. Connect the following PATS Ignition:
   • D6: White/Red
   • D5: White/Blue
   • D4: White/Green
   • D3: Yellow/Red
   • D2: Yellow/Blue
   • D1: Yellow/Green
5. Connect the following Ground:
   • E5: D5 Fuse
   • E6: A4 1780K Ohm resistor
6. Connect the following Trunk Release Lock:
   • A3: White/ Purple
7. Connect the following Unlock Disarm:
   • A6: White/ Black
8. Connect the following Brake:
   • A11: (+)
9. Connect the following (MUX) Parking Lights:
   • A12: White/ Green
10. Connect the following RX:
    • A10: Grey/ Red
11. Connect the following TX:
    • A20: White/ Red
12. Connect the following (+) Ignition and Starter:
    • D6: Orange/ Blue
13. Connect the following 12V:
    • E3: Red
14. Connect the following (+) Accessory1:
    • E2: Pink/ White
15. Connect the following (+) Accessory2:
    • E1: Yellow

REGULAR INSTALLATION

Vehicle functions supported in this diagram (functional if equipped)

MANDATORY INSTALL

WIRING CONNECTION

PROGRAM.1: 2 KEY PROGRAMMING PROCEDURE 1/2

PROGRAM.1: 2 KEY PROGRAMMING PROCEDURE 2/2

DCRYPTOR PROGRAMMING PROCEDURE

KEY BYPASS PROGRAMMING PROCEDURE 2/3

KEY BYPASS PROGRAMMING PROCEDURE 3/3

REMOTE STARTER PROGRAMMING PROCEDURE

REMOTE STARTER FUNCTIONALITY

Notice: Updated Firmware and Installation Guides
Updated fi rmware and installation guides are posted on our web site on a regular basis. We recommend that you update this module to the latest fi rmware and download the latest installation guide(s) prior to the installation of this product.

WARNING
The information on this sheet is provided on an (as is) basis with no representation or warranty of accuracy whatsoever. It is the sole responsibility of the installer to check and verify any circuit before connecting to it. Only a computer safe logic probe or digital multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or responsibility whatsoever pertaining to the accuracy or currency of the information supplied. The installation in every case is the sole responsibility of the installer performing the work and FORTIN ELECTRONIC SYSTEMS assumes no liability or responsibility whatsoever resulting from any type of installation, whether performed properly, improperly or any other way. Neither the manufacturer or distributor of this module is responsible of damages of any kind indirectly or directly caused by this module, except for the replacement of this module in case of manufacturing defects. This module must be installed by qualifi ed technician. The information supplied is a guide only. This instruction guide may change without notice. Visit www.fortinbypass.com to get the latest version.

TECH SUPPORT

• Tél: 514-255-HELP (4357)
• 1-877-336-7797
• ADDENDUM GUIDE
• www.fortinbypass.com.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>