MINKA LAVERY 1105-66A Robin Baron 3-Light Black Pendant Instruction Manual

June 13, 2024
MINKA LAVERY

MINKA LAVERY 1105-66A Robin Baron 3-Light Black Pendant

Product Information

This product is an item with the model number 1105-66A. It is a fixture designed for installation in a residential or commercial setting. The fixture includes a metal cover, thread rods, a canopy, a mounting plate, wire connectors, a glass shade, a plastic washer, a metal plate, a finial, and mounting screws.

Product Usage Instructions

  1. Before starting the installation process, ensure that the power is shut off at the fuse box or circuit breaker.
  2. Remove the old fixture and its mounting hardware.
  3. Unpack the new fixture and lay out all the parts in a clean area, taking care not to misplace any small parts.
  4. Assemble the fixture with the chain loop by placing the metal cover over all thread. Determine the desired hanging height and attach the thread rods to the all thread. Screw the canopy onto one of the rods and pass the wires through each rod during assembly.
  5. Attach the mounting plate to the junction box using the provided mounting screws. Ensure that the side of the mounting plate marked with GND faces out.
  6. Connect the electrical wires as shown in Fig. 2. Make sure all wire connectors are secured. If your junction box has a ground wire, connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate using the green screw provided.
  7. Tuck the wire connectors neatly into the junction box.
  8. Place the canopy over the mounting plate and secure it with screws.
  9. Thread all thread to the coupling and tighten with the hex nut. Adjust the top hex nut position if necessary.
  10. Install three medium base bulbs up to 100 watts each or CFL/LED equivalent, following the fixture’s specifications. Do not exceed the maximum wattage rating.
  11. Place the glass shade, plastic washer, and metal plate through the all thread, then secure with the hex nut.
  12. Screw the finial onto the all thread until tight.
  13. Once the installation is complete, return power to the junction box and test the fixture.

Note: The illustration in Fig. 1 is for installation purposes only and may not be identical to the fixture purchased.

INSTALLATION INSTRUCTIONS
Item#1105-66A New.2023/03/06)
READ AND SAVE THESE INSTRUCTIONS
WARNING ! SHUT POWER OF FAT FUSE OR CIRCUI T BREAKER .

PREPARATION (Fig. 1)

  1. Shut off power at the fuse box or circuit breaker box and remove the old fixture including the mounting hardware.

  2. Carefully unpack your new fixture and lay out all the parts in a clean area. Take care not to misplace any small parts necessary for installation.
    ASSEMBLING THE FIXTURE WITH CHAIN LOOP (Fig.1 &Fig. 3)

  3. Place metal cover (E) over all thread (G).

  4. Determine the desired hanging height and thread rods (F1, F2 and F3) to all thread (G). Attach canopy (C) by screwing onto rod (F1). Carefully pass the wires through each rod during assembly.

  5. Attach mounting plate (A) to the junction box (not included) with mounting screws (B) (Size: #8-32N*L0.5”). The side of the mounting plate (A) with “GND” marked on it and two convex points must face out.
    CONNECTING THE WIRES (Fig. 2)

  6. Connect the electrical wires as shown in fig 2, making sure that all wire connectors are secured. If your junction box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate (A) using the green screw provided.

  7. Tuck the wire connectors neatly into the junction box. COMPLETING THE INSTALLATION (Fig. 1)

  8. Place canopy (C) over mounting plate (A) and secure with screws (D).

  9. Thread all thread (K) to coupling (H) and tighten with hex nut (J). Adjust top hex nut position if necessary.

  10. Install (3) three medium base bulbs (I) up to 100 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification—DO NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!).

  11. Place glass shade (L), plastic washer (M), and metal plate (N) through all thread (K). Then secure with hex nut (J).

  12. Screw finial (P) onto all thread (K) until tight.

Your installation is now complete. Return power to the junction box and test the fixture.
Note: Illustration (Fig. 1) on this manual is for installation purposes only. It may or may not be identical to the fixture purchased.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

MINKA LAVERY User Manuals

Related Manuals