FORTIN 87711 2017 Volkswagen Golf Regular Key Remote Starters And Alarm Systems Installation Guide

REV.: 20221212
Guide # 87711
INSTALLATION WITH TB-VW
INSTALLATION AVEC TB-VW
ADDENDUM – SUGGESTED WIRING CONFIGURATION

87711 2017 Volkswagen Golf Regular Key Remote Starters And Alarm Systems

Golf MFD 01-2014 to 08-2014

COMPATIBLE MODULE REQUIRED:
OR CODE ON THE LABEL
MANUFACTURED AFTER: 2019
FIRMWARE VERSION VERSION LOGICIELLE
65.[04]
VW MINIMUM
To add the firmware version and the options. use the FLASH LINK UPDATER or FLASH LINK MOBILE tool, sold separately.
Golf MFD 09-2014 & +

COMPATIBLE MODULE REQUIRED:
OR CODE ON THE LABEL
MANUFACTURED AFTER: 2019
FIRMWARE VERSION VERSION LOGICIELLE
65.[06]
VW MINIMUM
To add the firmware version and the options. use the FLASH LINK UPDATER or FLASH LINK MOBILE tool, sold separately.

| Program bypass option
IF THE VEHICLE IS NOT EQUIPPED WITH FUNCTIONAL HOOD PIN:| UNIT OPTION OPTION UNITE| DESCRIPTION
---|---|---|---
A11| | Hood trigger (Output Status).

NOTES

Vehicle’s equipped with Virtual Cluster, not supported for the key bypass.

MANDATORY INSTALL

• HOOD PIN

HOOD STATUS : THE HOOD PIN SWITCH (INCLUDED)
MUST BE INSTALLED IF THE VEHICLE CAN BE
REMOTE STARTED WITH THE HOOD OPEN, SET FUNCTION A11 TO OFF.

A11|
---|---

SECURITY STICKER

Notice: the installation of safety elements are mandatory. The hood pin and the sticker are essential security elements and must be installed.
THIS MODULE MUST BE INSTALLED BY A QUALIFIED TECHNICIAN. A WRONG CONNECTION CAN CAUSE PERMANENT DAMAGE TO THE VEHICLE.

PARTS REQUIRED

| | UNIT OPTION
OPTION UNITE| DESCRIPTION
---|---|---|---
| Program bypass option:| C1| OEM Remote status (Lock/Unlock)
monitoring
Program bypass option (If equiped with OEM alarm):| D2| Unlock before / Lock after (Disarm OEM
alarm)
| Program remote
starter option for R.S. OEM
REMOTE STAND ALONE:| FUNCTION| MODE| DESCRIPTION
---|---|---|---|---
| 38| 5| Enable  (Press Lock, Unlock and Lock to remote start)
for COMFORT GROUP ACTIVATION:| 39| 2| Temperature option : AUX.1 activated at 5° C, 5 seconds after
remote started

WIRE TO WIRE DIAGRAM

| | Parts required (Not included)| PAGE
---|---|---|---
| AUTOMATIC TRANSMISSION| 1x TB-VW (key bypass)
1x RLINK programming tool
1x Fusible 7.5 Amp.| page 4
| MANUAL TRANSMISSION| 1x TB-VW (key bypass)
1x RLINK programming tool
1x 7.5 Amp. Fuse| page 5
| THARNESS DIAGRAM
THARNESS THAR-VW6| AUTOMATIC TRANSMISSION| 1x TB-VW (key bypass)
1x RLINK programming tool
1x THAR-VW6| page 6
THARNESS THAR-VW2| AUTOMATIC TRANSMISSION| 1x TB-VW (key bypass)
1x RLINK programming tool
1x THAR-VW2| page 8
MANUAL TRANSMISSION| 1x TB-VW (key bypass)
1x RLINK programming tool
1x THAR-VW2
1x Diode| page 9
| Parts required (Not included)
---|---
| 1x TB-VW (key bypass)
| PROGRAMMING TOOL REQUIRED for key bypass programming.
Sold separately.

PHOTOS & LOCATIONS

TB-VW MANUAL TRANSMISSION WIRING CONNECTION

TB-VW MANUAL TRANSMISSION WIRING CONNECTION

TB-VW – THAR-VW6 – AUTOMATIC TRANSMISSION WIRING CONNECTION

TB-VW – THAR-VW6 – MANUAL TRANSMISSION WIRING CONNECTION

TB-VW – THAR-VW2 – AUTOMATIC TRANSMISSION WIRING CONNECTION

TB-VW – THAR-VW2 – MANUAL TRANSMISSION WIRING CONNECTION

DCRYPTOR PROGRAMMING PROCEDURE

Parts required (not included)

|  FLASH LINK UPDATER,
---|---
| FLASH LINK MANAGER
SOFTWAR
| Microsoft Windows Computer with Internet connection
or
| FLASH LINK MOBILE
| FLASH LINK MOBILE APP
| Smartphone Android or iOS with Internet connection
(Internet provider charges may apply)

BEFORE PROGRAMMING SET THE UNIT OPTIONS AND SAVE.

*USE THE R-LINK TOOL FOR PROGRAMMING*
Sold separately

Connect the R-LINK instead of the TB-VW.

1. WARNING:
   Close and open the driver door.

2. Press and hold the
   programming button:
   Insert the 6-Pin Main connector.

WITH T-HARNESS
Press and hold the
programming button:
Connect the 4-PIN Data-link harness (Black connector).

3. Release the programming button when the Blue LED is ON.
   
   If the LED is not solid BLUE disconnect the 6-Pin connector (Main-Harness) and go back to step1.

4. Connect the required remaining harnesses.
   

5. Turn the key to the Ignition ON/RUN position.

CONTINUED NEXT PAGE
KEY BYPASS PROGRAMMING PROCEDURE 2/3

6. WITH T-HARNESS THAR-VW6

Press and release the programming button.
The BLUE LED will turn OFF.
The BLUE LED will turn off.
Wait,
The BLUE LED will flashrapidly.

7. Press and hold the programming button.
   The BLUE LED will turn OFF.
   Wait,
   The RED LED will turn ON.
   Release the programming button.
   

8. WAIT, this processe may take up to 5 minutes

Wait, do not touch the vehicle or the module.
The BLUE, RED and YELLOW
LEDs will rapidly alternate.
the RED LED to turn ON.
Wait,
  the YELLOW LED will flash once.

9. Wait,
   Wait for the RED and YELLOW
   LEDs to slowly alternate.

If the RED LED flashes slowly, the programming has failed, go back to step1 and start the programming over.

10. Turn the key to the OFF position.

KEY BYPASS PROGRAMMING PROCEDURE 3/3

11. Disconnect all connectors and after the 6-Pin (Main-Harness) or the 4-Pin Data-link connector.
    .

12. Microsoft Windows Computer with Internet connection*

Smartphone
(Internet provider charges may apply)
Use the tool:
FLASH LINK UPDATER or FLASH LINK MOBILE to visit the DCryptor menu.
Parts required (not included) 13. AFTER DCRYPTOR PROGRAMMING COMPLETED
Go back to the vehicle and reconnect the 6-Pin (MainHarness) or the 4-pins (Data-Link) connector and after all the remaining connector.

14. Connect the TB-VW instead of the R-LINK.
    

NOTE
IF PROGRAMMING IS INTERRUPTED DURING THE PROCESS, SUCH AS A MODULE IS DISCONNECTED OR BY TURNING OFF THE IGNITION WITH THE KEY, IT IS POSSIBLE THAT THE VEHICLE WILL NO LONGER START NORMALLY, YOU MUST DISCONNECT AND RECONNECT THE VEHICLE BATTERY TO CORRECT THE SITUATION.
The module is now programmed.
REMOTE STARTER / ALARM VERIFICATION
Test the remote starter. Remote start the vehicle.

REMOTE STARTER FUNCTIONALITY

MANUAL TRANSMISSION: READY MODE
BY DEFAULT

| The vehicle must be running.
---|---
| Make sure that all doors are closed and the  transmission is in the NEUTRAL position.
| Press the brake pedal.
| Engage the parking brake.
| Release the brake pedal.
| Press the START button for 3 seconds. The parking lights will flash once and then remain on.
| Remove the key from the ignition barrel : the vehicle will remain running with the Remote-Starter.
| Exit the vehicle and close all of the doors. The engine will stop running once all the doors are closed.
| Ready mode is now active, remote start is functional. If one of the doors is open the mode will be disabled.

CHOICE 2

| The vehicle must be running.
---|---
| Make sure that all doors are closed and the transmission is in the NEUTRAL position.
| Press the brake pedal.
| Engage the parking brake.
| Release the brake pedal.
| Press the START button for 3 seconds.  The parking lights will flash once and then remain on.
| Remove the key from the ignition barrel : the vehicle will remain running with the Remote-Starter.
| Exit the vehicle and close all of the doors.
| Lock the doors with the remote-starter remote or the OEM remote. The engine will stop running.
| Ready mode is now active, remote start is functional. If one of the doors is open the mode will be disabled.

CHOICE 3

| The vehicle must be running.
---|---
| Make sure that all doors are closed and the  transmission is in the NEUTRAL position.
| Press the brake pedal.
| Engage the parking brake.
| Release the brake pedal.
| Remove the key from the ignition barrel : the vehicle will remain running with the Remote-Starter.
| Exit the vehicle and close all of the doors. The engine will stop running once all the doors are closed.
| Ready mode is now active, remote start is functional. If one of the doors is open the mode will be disabled.

TAKE OVER AUTOMATIQUE TRANSMISSION

| All doors must be closed.
---|---
| Remote start the vehicle.
| Unlock the doors with the remote-starter remote or the OEM remote.
| Insert and Turn the key to the Ignition ON/RUN position.
| Press the brake pedal.
| The vehicle can now be put in to gear and driven.

REMOTE STARTER PROGRAMMING PROCEDURE

REFER TO THE QUICK INSTALL GUIDE INCLUDED WITH THE MODULE FOR THE REMOTE STARTER PROGRAMMING.

Module label

Notice: Updated Firmware and Installation Guides
Updated firmware and installation guides are posted on our web site on a regular basis. We recommend that you update this module to the latest firmware and download the latest installation guide(s) prior to the installation of this product.
WARNING
The information on this sheet is provided on an (as is) basis with no representation or warranty of accuracy whatsoever. It is the sole responsibility of the installer to check and verify any circuit before connecting to it. Only a computer safe logic probe or digital multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or responsibility whatsoever pertaining to the accuracy or currency of the information supplied. The installation in every case is the sole responsibility of the installer performing the work and FORTIN ELECTRONIC SYSTEMS assumes no liability or responsibility whatsoever resulting from any type of installation, whether performed properly, improperly or any other way. Neither the manufacturer or distributor of this module is responsible of damages of any kind indirectly or directly caused by this module, except for the replacement of this module in case of manufacturing defects. This module must be installed by qualifi ed technician. The information supplied is a guide only. This instruction guide may change without notice. Visit www.fortinbypass.com to get the latest version.

Copyright © 2006-2019, FORTIN AUTO RADIO INC ALL RIGHTS RESERVED PATENT PENDING
This guide may change without notice. See www.fortin.ca for latest version.

TECH SUPPORT
Tél: 514-255-HELP (4357)
1-877-336-7797
ADDENDUM GUIDE
www.fortinbypass.com
WEB UPDATE

References

• Over

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>