MINKA LAVERY 2663-717 Colonial Charm 3-Light White Wash and Sun Dried Clay Candlestick Chandelier Instruction Manual

MINKA LAVERY 2663-717 Colonial Charm 3-Light White Wash and Sun Dried

Clay Candlestick Chandelier

Product Information

• Product Name: Item#2663-723
• Date of Manufacture: New. 04/02/2022
• Model: LA-3499E

Installation Instructions

1. Shut off the power at the fuse box or circuit breaker before starting the installation.
2. If necessary, remove the old fixture, including mounting hardware.
3. Carefully remove the fixture from the carton and ensure all parts are included as shown in the illustration.
4. Adjust the arms (I) to the proper position based on the provided illustration (L).
5. Screw the fixture loop (A) to the coupling (B).
6. Thread the all thread into the ceiling loop until snug.
7. Thread the other end of the all thread into the crossbar.

Connecting the Wires

Follow the provided illustration (Fig. 3) to connect the electrical wires:

• Connect the fixture’s black or smooth wire to the house’s black (hot) wire.
• Connect the fixture’s white or ribbed wire to the house’s white (neutral) wire.
• If your outlet box has a green or bare copper ground wire, connect the fixture’s bare copper ground wire to it. Otherwise, connect the fixture’s ground wire directly to the crossbar using the provided green screw.
• Tuck all wire connections neatly into the outlet box.
• Raise the canopy to the ceiling and secure it with the lock collar.

Finishing the Installation

1. Place the bobeches (K) over the candle covers (J).
2. Hang the wooden drops (D, M, N, O) onto the fixture body in the proper position.
3. Thread the finial (H) to the fixture body and attach the wooden drop (O).
4. Install three candelabra base bulbs up to 60 watts each or CFL or LED equivalent (not included) according to the fixture’s specifications. Do not exceed the maximum wattage rating.

Note: The illustration in Fig. 1 is for installation purposes only and may not be identical to the fixture purchased.

Additional Notes:
It is important to use proper chain pliers (not included) to open and close the chain included with this fixture. Do not use other tools that may twist or stress the chain links. Refer to the provided diagram for proper chain pliers.

Your installation is now complete. Restore power to the outlet box and test the fixture.

INSTALLATION INSTRUCTIONS
Item#2663-723 (New. 04/02/2022)
READ AND SAVE THESE INSTRUCTIONS
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.

ASSEMBLING THE FIXTURE

(Fig. 1)

Set# A-010
-Crossbar
-Ground screw
-Mounting Screw *2
Candle Cover # CCV21080P-737

1. Shut off the power at the fuse box or circuit breaker. If necessary, remove old fixture, including mounting hardware.

2. Carefully remove fixture from carton and check that all parts are included as shown in the illustration.

3. Adjust the arms (I) to proper position. Refer to illustration (L).

4. Screw fixture loop (A) to coupling (B).
   MOUNTING THE FIXTURE (Fig. 2)

5. Thread all thread into ceiling loop until snug.

6. Thread the other end of the all thread into crossbar. Note: The length of the all thread into crossbar may be adjusted if necessary.

7. Secure all thread to crossbar with hex nut.

8. Take crossbar assembly and mount it to outlet box using the mounting screws (Size: #8-32N*L1”). The side of crossbar marked “GND” must face out.

9. Open quick link and connect to fixture loop, then close quick link.

10. By measuring, determine the correct number of links needed for desired hanging height. Using chain pliers, disconnect and discard excess chain.

11. Carefully lace fixture wires through chain.

12. Slip lock collar and canopy over chain and allow them to rest on fixture body.

13. Open the quick link and attach it to the ceiling loop, then close quick link.

14. Carefully feed fixture wires through ceiling loop and all thread and pull until tight.
    CONNECTING THE WIRES (Fig. 3)

15. Connect the electrical wires as shown in Fig. 3 making sure that all wire connectors are secured. If your outlet box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the crossbar using the green screw provided.

16. Tuck wire connections neatly into outlet box. Raise canopy to ceiling and secure with lock collar.
    FINISHING THE INSTALLATION (Fig.1)

17. Place bobeches (K) over candle covers (J).

18. Hang wooden drops (D,M,N,O) onto fixture body in proper position.

19. Thread finial (H) to fixture body and attach wooden drop (O).

20. Install (3) three candelabra base bulbs up to 60 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification—DO NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!).
    Your installation is now complete. Return power to the outlet box and test the fixture.

Note: Illustration (Fig. 1) on this manual is for installation purposes only. It may or may not be identical to the fixture purchased.

Notice: It is important to use proper chain pliers (not included)
To OPEN and CLOSE the chain included with this fixture. Do not open them with other tools that may twist or stress the chain links. It is important to use proper chain pliers like the ones shown in the diagram.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>