MINKA LAVERY 4586-672 Caprio 6-Light Natural Brushed Brass Pendant Instruction Manual

MINKA LAVERY 4586-672 Caprio 6-Light Natural Brushed Brass Pendant

Product Information

The product is a fixture with model number 4586-672. It is intended for installation in a residential or commercial setting. The fixture includes a crystal ball, fabric shade, arms, decorative ring, rods, quick link, circular strap, junction box screws, support cable, hook, ground screw, mounting screws, candle covers, tube covers, candelabra base bulbs, leaf finial, and hex nuts.

Product Usage Instructions

1. Before starting the installation, ensure that the power is shut off at the fuse box or circuit breaker.

2. Remove the old fixture and its mounting hardware.

3. Carefully unpack the new fixture and lay out all the parts in a clean area.

4. Attach the crystal ball onto the tube.

5. Install the fabric shade on the arms using the metal nuts and place the decorative ring on the fabric shade.

6. Determine the desired height and thread the rods together.
   Screw the loop to one of the rods. Pass the wires carefully through each rod as you assemble. Attach the bottom end of the rod into the coupling.

7. Attach the quick link to the loop on the canopy. Carefully feed the wire through the loop, quick link, and another loop.

8. Attach the circular strap to the junction box using the junction box screws. Ensure that the side marked GND faces out. The mounting screw can be adjustable if necessary.

9. Use the support cable provided to support the weight of the fixture while wiring. Align the fixture to the circular strap and attach the hook on the end of the support cable into a slot located on the circular strap. Allow the support cable to support the weight of the fixture while wiring.

10. Connect the electrical wires as shown in Figure 2. Ensure that all wire connectors are secured. If your junction box has a ground wire, connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the circular strap using the green screw provided. Tuck the wire connectors neatly into the junction box.

11. Raise the fixture over the mounting screws and secure it with decorative nuts.

12. Place candle covers over sockets, then place tube covers over candle covers.

13. Install six candelabra base bulbs up to 60 watts each or CFL or LED equivalent in accordance with the fixture specification. Do not exceed the maximum wattage rating.

14. Attach the leaf finial with the coupling.

15. The installation is now complete. Turn on the power supply of the junction box to test the fixture.

Note: The illustration in Figure 1 is for installation purposes only and may not be identical to the fixture purchased.

INSTALLATION INSTRUCTION FOR FIXTURE #4586-672

WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR

ASSEMBLY THE FIXTURE

(FIG. 1 &FIG.3)

1. Shut off power at the fuse box or circuit breaker box and remove the old fixture including the mounting hardware.

2. Carefully unpack your new fixture and lay out all the parts in a clean area. Take care not to misplace any small parts necessary for installation.

3. Attach crystal ball (T) onto tube (S).

4. Install fabric shade (M) on arms (R) using metal nuts (N) and place decorative ring (L）on fabric shade (M).

5. Determine the desired height and thread rods (G1 and G2) together. Screw loop (I1) to the rod (G1). Pass the wires carefully through each rod as you assemble. Attach the bottom end of rod into the coupling (J).

6. Attach quick link (H) to loop (I2) on canopy (D). Carefully feed the wire through loop (I1), quick link (H), and loop (I2).

7. Attach circular strap (B) to the junction box using the junction box screws (C). The side of the circular strap (B) marked “GND” must face out. Mounting screw can be adjustable if necessary.

8. The support cable is provided to support the weight of the fixture while wiring. Align the fixture to circular strap (B) and attach hook on the end of support cable (E) into a slot located on circular strap (B). Carefully allow the support cable (E) to support the weight of the fixture while wiring.
   CONNECTING THE WIRES (FIG. 2)

9. Connect the electrical wires as shown in figure 2, making sure that all wire connectors are secured. If your junction box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the circular strap (B) using the green screw provided.

10. Tuck the wire connectors neatly into the junction box.
    COMPLETING THE INSTALLATION (Fig. 1)

11. Raise the fixture over the mounting screws (A) and secure with decorative nuts (F).

12. Place candle covers (Q) over sockets (V), then place tube covers (K) over candle covers (Q). Install (6) six candelabra base bulbs (X) up to 60 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification—DO NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!).

13. Attached leaf finial (O) with coupling (P).

The leaves on the lamp body can be manually adjusted to change their shape.
Your installation is now complete. Turn on the power supply of the junction box to test the fixture.

Note: Illustration (Fig. 1) on this manual is for installation purposes only. It may or may not be identical to the fixture purchased.

Hardware Bag:

• A. Mounting Screw*2
• B. Circular Strap*1
• C. Screw*2
• D. Canopy*1
• F. Decorative Nuts*2
• H. Quick Link*1
• I. Loop2 AA. Hex Nuts2

Hardware Bag:

• G1. ROD 6″*1
• G2. ROD 12″*3

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>