MINKA LAVERY 4584-672 Caprio 4-Light Natural Brushed Brass Pendant Instruction Manual

MINKA LAVERY 4584-672 Caprio 4-Light Natural Brushed Brass Pendan

Product Information: Installation Instruction

The installation instruction provides step-by-step guidance on how to assemble and install Fixture #4584-672. It includes warnings, assembly instructions, wire connection instructions, and completion of the installation. The instruction also provides a diagram (Fig. 1) for reference. The fixture includes a crystal ball (T), fabric shade (M), arms (R), metal nuts (N), decorative ring (L), rods (G1 and G2), loop (I1), coupling (J), quick link (H), circular strap (B), junction box screws (C), support cable (E), hook, electrical wires, ground wire, mounting screws (A), decorative nuts (F), candle covers (Q), tube covers (K), candelabra base bulbs (X), leaf finial (O), and coupling (P).

Product Usage Instructions

1. Before starting the installation, shut off the power at the fuse box or circuit breaker box.

2. Remove the old fixture and its mounting hardware carefully.

3. Unpack the new fixture and lay out all the parts in a clean area.

4. Attach the crystal ball (T) to the tube (S).

5. Install the fabric shade (M) on the arms (R) using the metal nuts (N) and place the decorative ring (L) on the fabric shade.

6. Determine the desired height and thread rods (G1 and G2) together. Screw loop (I1) to rod (G1). Pass the wires carefully through each rod as you assemble. Attach the bottom end of the rod into the coupling (J).

7. Attach the quick link (H) to loop (I2) on the canopy (D). Carefully feed the wire through loop (I1), quick link (H), and loop (I2).

8. Attach the circular strap (B) to the junction box using the junction box screws (C). Ensure that the side of the circular strap (B) marked GND is facing out. Adjust the mounting screw if necessary.

9. Use the support cable (E) to support the weight of the fixture while wiring. Align the fixture to the circular strap (B) and attach the hook on the end of the support cable (E) into a slot located on the circular strap (B). Allow the support cable (E) to support the weight of the fixture while wiring.

10. Connect the electrical wires as shown in Fig. 2. Ensure that all wire connectors are secured. If your junction box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the
    circular strap (B) using the green screw provided. Neatly tuck the wire connectors into the junction box.

11. Raise the fixture over the mounting screws (A) and secure it with decorative nuts (F).

12. Place candle covers (Q) over sockets (V), then place tube covers (K) over candle covers (Q). Install four candelabra base bulbs (X) up to 60 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification. Do not exceed the maximum wattage rating.

13. Attach the leaf finial (O) with coupling (P).

14. The installation is now complete. Turn on the power supply of the junction box to test the fixture.

Note: The illustration in Fig. 1 is for installation purposes only and may or may not be identical to the fixture purchased.

ASSEMBLING THE FIXTURE

Fig. 1 & Fig. 4

1. Shut off power at the fuse box or circuit breaker box and remove the old fixture, including mounting hardware.
2.  Carefully unpack your new fixture from the carton and check that all parts are included as shown in the illustration.
3.  Adjust arms to the proper position. (Fig.4)
4.  Determine the desired hanging height and thread rods (B & C) to coupling (D)， and carefully feed wires through each rod as you assemble.
5.  Attach fixture loop (A) by threading onto rod (B).
6.  Attach cap (F) with screws (G) to hole (E) of the fixture. HANGING THE FIXTURE Fig. 2
7.  Thread all thread into the ceiling loop until snug.
8. Thread the other end of all thread into the crossbar, then use a lock washer and hex nut to secure all thread into the crossbar. Note: The length of all thread into crossbar may be adjusted if necessary.
9. Take the crossbar assembly and mount it to the ceiling outlet box (Not included) with mounting screws (Size: #8-32N*L1”). The side of crossbar marked with “GND” must face out.
10. Thread the other end of all thread into the crossbar, then use lock washer and hex nut to secure all thread into the crossbar. Note: The length of all thread into crossbar may be adjusted if necessary.

Take the crossbar assembly and mount it to the ceiling outlet box (Not included) with mounting screws (Size: #8-32N*L1”). The side of crossbar marked with “GND” must face out.

CONNECTING THE WIRE Fig. 3

1. Connect the electrical wire as shown in Fig. 3, making sure that all wire connectors are secured. If your outlet box has a ground wire (green or bare copper), connect fixtures ground wire to it. Otherwise, connect fixture ground wire directly to crossbar
2. ing green screw provided.
3. Tuck wire connections neatly into the outlet box and then raise the canopy all the way to the ceiling.

Raise the lock collar and thread onto the ceiling loop protruding through the canopy.

FINISHING THE FIXTURE Fig.1

1.  Install (5) five candelabra base bulbs (H) up to 60 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification — DO NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE
   Note: The illustration (Fig. 1) on this manual is for installation purposes only. It may or may not be identical to the fixture purchased.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>