MINKA LAVERY 2665-717 Colonial Charm 5-Light White Wash and Sun Dried Clay Candlestick Chandelier Instruction Manual

MINKA LAVERY 2665-717 Colonial Charm 5-Light White Wash and Sun Dried

Clay Candlestick Chandelier

Product Information

• Product Name: Fixture Item#2665-723
• Date of Manual: 04/02/2022
• Installation Instructions: Read and save these instructions

Installation Instructions

1. Step 1: Shut off the power at the fuse box or circuit breaker. If necessary, remove the old fixture, including mounting hardware.
2. Step 2: Carefully remove the fixture from the carton and check that all parts are included as shown in the illustration.
3. Step 3: Adjust the arms (I) to the proper position. Refer to the illustration (L).
4. Step 4: Screw the fixture loop (A) to the coupling (B).
5. Step 5: Thread the all thread into the ceiling loop until snug.
6. Step 6: Thread the other end of the all thread into the crossbar.
7. Step 7: Connect the electrical wires as shown in Fig. 3, making sure that all wire connectors are secured. If your outlet box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the crossbar using the green screw provided.
8. Step 8: Tuck wire connections neatly into the outlet box. Raise the canopy to the ceiling and secure it with a lock collar.
9. Step 9: Place bobeches (K) over candle covers (J).
10. Step 10: Hang wooden drops (D, E, F) onto the fixture body in the proper position.
11. Step 11: Thread the finial (H) to the fixture body and attach the wooden drop (G).
12. Step 12: Install (5) five candelabra base bulbs up to 60 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification. DO NOT EXCEED THE MAXIMUM WATTAGE RATING!

Your installation is now complete. Return power to the outlet box and test the fixture.

Note:
The illustration (Fig. 1) on this manual is for installation purposes only. It may or may not be identical to the fixture purchased.

Fixture Wires:

• Black or Smooth: Fixture wires
• White or Ribbed: Fixture wires
• Black (Hot): House wires
• Bare Copper (Ground): Fixture wires
• White (Neutral): House wires
• Green (Ground): House wires

Notice:
It is important to use proper chain pliers (not included) to open and close the chain included with this fixture. Do not open them with other tools that may twist or stress the chain links. Use proper chain pliers like the ones shown in the diagram.

INSTALLATION INSTRUCTIONS

ASSEMBLING THE FIXTURE (Fig. 1)

1. Shut off the power at the fuse box or circuit breaker. If necessary, remove old fixture, including mounting hardware.

2. Carefully remove fixture from carton and check that all parts are included as shown in the illustration.

3. Adjust the arms (I) to proper position. Refer to illustration (L).

4. Screw fixture loop (A) to coupling (B).
   MOUNTING THE FIXTURE (Fig. 2)

5. Thread all thread into ceiling loop until snug.

6. Thread the other end of the all thread into crossbar. Note: The length of the all thread into crossbar may be adjusted if necessary.

7. Secure all thread to crossbar with hex nut.

8. Take crossbar assembly and mount it to outlet box using the mounting screws (Size: #8-32N*L1”). The side of crossbar marked “GND” must face out.

9. Open quick link and connect to fixture loop, then close quick link.

10. By measuring, determine the correct number of links needed for desired hanging height. Using chain pliers, disconnect and discard excess chain.

11. Carefully lace fixture wires through chain.

12. Slip lock collar and canopy over chain and allow them to rest on fixture body.

13. Open the quick link and attach it to the ceiling loop, then close quick link.

14. Carefully feed fixture wires through ceiling loop and all thread and pull until tight.
    CONNECTING THE WIRES (Fig. 3)

15. Connect the electrical wires as shown in Fig. 3 making sure that all wire connectors are secured. If your outlet box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the crossbar using the green screw provided.

16. Tuck wire connections neatly into outlet box. Raise canopy to ceiling and secure with lock collar.
    FINISHING THE INSTALLATION (Fig.1)

17. Place bobeches (K) over candle covers (J).

18. Hang wooden drops (D,E,F) onto fixture body in proper position.

19. Thread finial (H) to fixture body and attach wooden drop (G).

20. Install (5) five candelabra base bulbs up to 60 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification—DO NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!).
    Your installation is now complete. Return power to the outlet box and test the fixture.

Note : Illustration (Fig. 1) on this manual is for installation purposes only. It may or may not be identical to the fixture purchased.
Notice : It is important to use proper chain pliers (not included) To OPEN and CLOSE the chain included with this fixture. Do not open them with other tools that may twist or stress the chain links. It is important to use proper chain pliers like the ones shown in the diagram.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>