Minka-Lavery 5908-655 North Folk Modern Sand White Chandelier Light Installation Guide
- June 13, 2024
- MINKA LAVERY
Table of Contents
Minka-Lavery 5908-655 North Folk Modern Sand White Chandelier Light
Product Information
This product is a light fixture with item number 5908-655. It comes with various parts and hardware necessary for installation. The fixture includes a crossbar, a ground screw, junction box screws, a rod, a candle cover, and fixture wires. The installation should be done after shutting off the power at the fuse box or circuit breaker.
Product Usage Instructions
- Begin by shutting off the power at the fuse box or circuit breaker.
- Remove the old fixture along with its mounting hardware.
- Carefully unpack the new fixture and lay out all the parts.
- Identify the fixture wires and house wires:
- Fixture Wires: Black or Smooth wire, White or Ribbed wire, Bare Copper (Ground) wire
- House Wires: Black (Hot) wire, White (Neutral) wire, Green (Ground) wire
- Connect the wires:
- Connect the Black (Hot) house wire to the Black or Smooth fixture wire.
- Connect the White (Neutral) house wire to the White or Ribbed fixture wire.
- Connect the Green (Ground) house wire to the Bare Copper fixture wire.
- Securely fasten all the connections using appropriate connectors.
- Follow the specific instructions for mounting the fixture based on the provided diagram (Fig. 1).
- Once the fixture is mounted, return power to the junction box.
- Test the fixture to ensure it is functioning properly.
Note: The illustration provided in the manual (Fig. 1) is for installation purposes only and may not be identical to the fixture purchased.
INSTALLATION INSTRUCTIONS
Item#5908-655 (New.12/28/2022)
READ AND SAVE THESE INSTRUCTIONS
WARNING ! SHUT POWER OF FAT FUSEOR CIRCUIT BREAKER .
PREPARATION (Fig. 1)
-
Shut off power at the fuse box or circuit breaker box and remove the old fixture including the mounting hardware.
-
Carefully unpack your new fixture and lay out all the parts in a clean area. Take care not to misplace any small parts necessary for installation.
ASSEMBLING THE FIXTURE (Fig.1 &Fig.3) -
Adjust the arms to proper position. Refer to illustration (K).
-
Thread rod (H3) to fixture body (L), determine the desired hanging height and thread rods (H1, H2) to rod (H3). Then screw loop (G) to rod (H1 or H2). Pass the wires carefully through each rod as you assembled.
-
Thread all thread into ceiling loop (C) until snug.
-
Thread the other end of the all thread into crossbar (A) and secure with hex nut (M). Note: The length of the all thread into crossbar may be adjusted if necessary.
-
Take crossbar assembly and mount it to junction box (not included) using the junction box screws (B) (Size: #8-32N*L1”). The side of crossbar marked “GND” must face out.
-
Slip lock collar (E) and canopy (D) over rods and allow them to rest on fixture body.
-
Open quick link (F) and attach it to canopy loop (C) and fixture loop (G), then close quick link (F).
-
Carefully feed fixture wires through ceiling loop (C) and all thread and pull until tight.
CONNECTING THE WIRES (Fig. 2)
-
Connect the electrical wires as shown in Fig. 2 making sure that all wire connectors are secured. If your junction box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the crossbar (A) using the green screw provided.
-
Tuck wire connections neatly into junction box. Raise canopy (D) to junction box and secure with lock collar (E).
COMPLETING THE INSTALLATION (Fig. 1) -
Place “flower” (J) over candle covers (I).
-
Install (12) twelve candelabra base bulbs up to 60 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification—DO NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!)
Your installation is now complete. Return power to the junction box and test
the fixture.
Note: Illustration (Fig. 1) on this manual is for installation purposes
only. It may or may not be identical to the fixture purchased.
a. Hardware Bag
- A. Crossbar x 1pc
- B. Junction Box Screw x 2pcs
- C. Ceiling Loop x1pc
- D. Canopy x 1pc
- E. Lock Collar x1pc
- F. Quick Link x 1pc
- G. Loop x 1pc
- M.Hex Nut x3pcs
b. Hardware Bag
- H1. Rod 6” x1pc
- H2. Ro d 12” x3pcs
- H3. Rod 13.4” x1pc
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>