Minka Lavery 4102 Series Parsons Studio 1 Light Brushed Nickel Drum Pendant Instruction Manual

Minka Lavery 4102 Series Parsons Studio 1 Light Brushed Nickel Drum

Pendant

Product Information: The product is an item with the model number 4102-66/84/172, which is a new model released on December 30, 2022. It is a fixture that requires installation and comes with a mounting plate, ground screw, mounting screws, rods, canopy, glass shades, metal cover and ring, screw shell, and a medium base bulb (not included). The fixture has specific instructions for installation and wiring connections to ensure proper usage.

Product Usage Instructions

Preparation:

1. Shut off power at the fuse box or circuit breaker box.
2. Remove the old fixture, including the mounting hardware.
3. Unpack the new fixture and lay out all the parts in a clean area. Take care not to misplace any small parts.
4. Determine the desired hanging height and thread rods (F1, F2, and F3) onto all thread (G).
5. Attach the canopy (D) by threading it onto rod (F1) and carefully pass wires through each rod during assembly.
6. Attach mounting plate (A) to the junction box with mounting screws (B). Ensure that the side of the mounting plate with “GND” marked on it and two convex points face out.

Connecting the Wires: Connect the electrical wires as shown in Fig 2:

• If your junction box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate (A) using the green screw provided.
• Tuck wire connectors neatly into the junction box.

Completing the Installation:

1. Place the canopy (D) over the mounting plate (A) and secure it with screws (E).
2. Place the large glass shade (I), metal cover (J), small glass shade (K), and metal ring (L) over the socket (H), then secure them with screw shell (M).
3. Install one medium base bulb (N) up to 100 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification. Do not exceed the maximum wattage rating.
4. Return power to the junction box and test the fixture.

Note: The illustration in Fig. 1 is for installation purposes only and may or may not be identical to the fixture purchased.

Item#4102-66/84/172 (New. 2022/12/30)
READ AND SAVE THESE INSTRUCTIONS
WARNING ! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.

INSTALLATION INSTRUCTIONS

PREPARATION (Fig.1)

1. Shut off power at the fuse box or circuit breaker box and remove the old fixture including the mounting hardware.

2. Carefully unpack your new fixture and lay out all the parts in a clean area. Take care not to misplace any small parts necessary for installation.

3. Determine the desired hanging height and thread rods (F1, F2 and F3) onto all thread (G). Attach canopy (D) by threading onto rod (F1). Carefully pass wires through each rod during assembly.

4. Attach mounting plate (A) to the junction box (not included) with mounting screws (B) (Size: #8-32N*L0.5”).
   The side of the mounting plate (A) with “GND” marked on it and two convex points must face out.
   CONNECTING THE WIRES (Fig. 2)

5. Connect the electrical wires as shown in Fig 2, making sure that all wire connectors are secured. If your junction box has a ground wire (green or bare copper), connect fixture’s ground wire to it. Otherwise, connect fixture’s ground wire directly to the mounting plate (A) using green screw provided.

6. Tuck wire connectors neatly into the junction box.
   COMPLETING THE INSTALLATION (Fig. 1)

7. Place canopy (D) over mounting plate (A) and secure with screws (E).

8. Place large glass shade (I), metal cover (J), small glass shade (K), metal ring (L) over the socket (H), then secure with screw shell (M).

9. Install (1) one medium base bulb (N) up to100 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification. —DO NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!)
   Your installation is now complete. Return power to the junction box and test the fixture.
   Note: Illustration (Fig. 1) on this manual is for installation purposes only. It may or may not be identical to the fixture purchased.

Fig. 1
Set# A-021-118DH

• Mounting plate
• Ground screw
• Mounting screw *2

Rod# W30-1-66/84/172 1 (F1) W30-1-66/84/172 2 (F2) W30-H-66/84/172 *1 (F3)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>