Minka Lavery 4102-84 Parsons Studio 1 Light Sand Black Drum Pendant Instruction Manual
- June 13, 2024
- MINKA LAVERY
Table of Contents
Minka Lavery 4102-84 Parsons Studio 1 Light Sand Black Drum Pendant
Product Information
The product is an item with the model number 4102-66/84/172. It is a fixture that needs to be installed and comes with specific installation instructions. The product is designed to be connected to a power source using electrical wires.
Product Usage Instructions
- Before starting the installation, ensure that the power is shut off at the fuse box or circuit breaker.
- Remove the old fixture and its mounting hardware.
- Unpack the new fixture and lay out all the parts in a clean area. Take care not to misplace any small parts.
- Attach the provided mounting plate to the junction box using the provided mounting screws. Make sure that the side of the mounting plate with “GND” marked on it and two convex points face out.
- Connect the electrical wires according to the diagram shown in Fig. 2. Ensure that all wire connectors are secured. If your junction box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate using the green screw provided. Tuck wire connectors neatly into the junction box.
- Place the canopy over the mounting plate and secure it with screws.
- Assemble the large glass shade, metal cover, small glass shade, metal ring, and screw shell over the socket. Secure them with the provided screw.
- Install one medium base bulb up to 100 watts each or CFL or LED equivalent (not included) according to the fixture specification. Do not exceed the maximum wattage rating.
- Once the installation is complete, return power to the junction box and test the fixture.
Note : The illustration in Fig. 1 is for installation purposes only and may or may not be identical to the fixture purchased.
INSTALLATION INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS
WARNING! SHUT THE POWER OFF AT THE FUSE OR CIRCUIT BREAKER.
PREPARATION
(Fig.1)
- Shut off power at the fuse box or circuit breaker box and remove the old fixture including the mounting hardware.
- Carefully unpack your new fixture and lay out all the parts in a clean area. Take care not to misplace any small parts necessary for installation.
- Determine the desired hanging height and thread rods (F1, F2 and F3) onto all thread (G). Attach canopy (D) by threading onto rod (F1). Carefully pass wires through each rod during assembly.
- Attach mounting plate (A) to the junction box (not included) with mounting screws (B) (Size: #8-32N*L0.5”). The side of the mounting plate (A) with “GND” marked on it and two convex points must face out.
CONNECTING THE WIRES
(Fig. 2)
-
Connect the electrical wires as shown in Fig 2, making sure that all wire connectors are secured. If your junction box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate (A) using the green screw provided.
-
Tuck wire connectors neatly into the junction box.
COMPLETING THE INSTALLATION (Fig. 1) -
Place canopy (D) over mounting plate (A) and secure with screws (E).
-
Place large glass shade (I), metal cover (J), small glass shade (K), and metal ring (L) over the socket (H), then secure with screw shell (M).
-
Install (1) one medium base bulb (N) up to 100 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification.
- DO NOT EXCEED THE MAXIMUM WATTAGE RATING!
Your installation is now complete. Return power to the junction box and test the fixture.
Note : The illustration (Fig. 1) in this manual is for installation purposes only. It may or may not be identical to the fixture purchased.
LA-3619E
Item#4102-66/84/172 (New. 2022/12/30)
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>