Minka Lavery 6201-44 Vantage 1 Light Brushed Nickel Metal Shade Pendant Instruction Manual

Minka Lavery 6201-44 Vantage 1 Light Brushed Nickel Metal Shade Pendant

Product Information

• Product Name: Item#6201-44/66A/84
• Date of Manufacture: 01/05/2023
• Product Type: Fixture
• Maximum Wattage Rating: 60 watts
• Compatibility: Medium base (E26) bulb or CFL or LED equivalent

Product Usage Instructions

1. Before starting the installation, ensure that the power is shut off at the fuse or circuit breaker box.
2. Mounting the Fixture:
   • Refer to Fig.1 for the mounting process.
   • Shut off power at the fuse box or circuit breaker box.
3. Connecting the Wires:
   • Refer to Fig.2 for the wire connections.
   • Connect the electrical wires as shown in Fig.2, ensuring that all wire connectors (A) are secured.
   • If your outlet box has a ground wire (green or bare copper), connect the fixture’s ground wire to it.
   • If there is no ground wire in the outlet box, connect the fixture’s ground wire directly to the mounting plate (B) using the green screw provided.
   • Tuck wire connections neatly into the outlet box.
4. Finishing the Installation:
   • Refer to Fig.1 for the finishing steps.
   • Place the canopy (E) over the mounting plate (B) and secure it with screws (D).
   • Install one medium base (E26) bulb (G) up to 60 watts each or CFL or LED equivalent (not included) according to the fixture specification. Do not exceed the maximum wattage rating.
5. After completing the installation, restore power and test the fixture to ensure proper functioning.

Note: The illustration in Fig.1 is for installation purposes only and may or may not be identical to the fixture purchased.
Important: It is recommended to have the fixture installed by a qualified electrician to ensure proper wiring and installation.

MOUNTING THE FIXTURE

1. Shut off power at the fuse box or circuit breaker box and remove the old fixture, including the mounting hardware.

2. Carefully unpack your new fixture and lay out all the parts in a clear area. Take care not to misplace any small parts necessary for installation.

3. Attach the mounting plate (B) to outlet box (not included) using outlet box screws (C) (SIZE: #8-32N, L0.5″). The side of the mounting plate (B) marked “GND” must face out.

4. Adjust the wire to desired hanging length using the small screw located on the side of the wire grip (F) with a flathead screwdriver (not included).

5. Ensure to re-tighten the set screw after wire adjustment. To straighten the cord, please use a blow dryer (not included) if necessary.

6. Remove any excess wire leaving approximately 7″ beyond canopy (E) for wire connections.
   CONNECTING THE WIRES (Fig.2)

7. Connect the electrical wires as shown in Fig.2, making sure that all wire connectors (A) are secured.

8. If your outlet box has a ground wire (green or bare copper), connect the fixture’s ground wire to it.

9. Otherwise, connect the fixture’s ground wire directly to the mounting plate (B) using the green screw provided.

10. Tuck wire connections neatly into the outlet box. FINISHING THE INSTALLATION (Fig.1)

11. Place canopy (E) over mounting plate (B) and secure with screws (D).

12. Install (1) one medium base (E26) bulb (G) up to 60 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification—DO NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!). Your installation is now complete. Return power and test the fixture

Note
The illustration (Fig.1) in this manual is for installation purposes only. It may or may not be identical to the fixture purchased.

IMPORTANT
THE FIXTURE SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN TO ENSURE PROPER WIRING AND INSTALLATION.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>