MINKA LAVERY 2469744 1-Light Wall Sconce In Brushed Nickel With Etched Opal Glass Shade Instruction Manual
- June 13, 2024
- MINKA LAVERY
Table of Contents
MINKA LAVERY 2469744 1-Light Wall Sconce In Brushed Nickel With Etched
Opal Glass Shade
Product Information
- Product Name: Item#342
- Date of Manufacture: 02/20/2012
- Manufacturer: Unknown
- Model Number: A-020
- Product Type: Fixture
Product Usage Instructions
- Before starting the installation process, ensure that the power is shut off at the fuse box or circuit breaker.
- Carefully unpack the fixture and check that all parts are included as shown in the illustration.
- If there is an existing fixture, remove it along with the mounting hardware. Otherwise, proceed to the next step.
- Attach the circular strap (A) over the outlet box using the provided mounting screws (B). Make sure that the side marked GND is facing out.
- Thread the two studs (C) partially into the circular strap (A).
- Connect the electrical wires as shown in figure 2. Secure all wire connectors properly. If your outlet box has a ground wire, connect the fixture’s ground wire to it using the wire connectors. If not, connect the fixture’s ground wire directly to the crossbar using the provided green screw.
- Tuck the connected wires carefully into the ceiling junction box.
- Place the backplate (E) over the two studs (C) and secure it against the wall using the two cap nuts (D).
- Install the light bulb(s) according to the fixture’s specifications. Make sure not to exceed the maximum wattage rating.
- Slide the glass (F) onto the backplate (E) and set it into place.
- Turn on the power at the junction box and test the fixture.
Note:
The illustration provided in the manual (Fig. 1) is for installation purposes
only and may not be identical to the fixture you purchased.
INSTALLATION INSTRUCTIONS
- Item#342 (New. 02/20/2012)
READ AND SAVE THESE INSTRUCTIONS
WARNING!
SHUT THE POWER OFF AT THE FUSE OR CIRCUIT BREAKER.
MOUNTING THE FIXTURE (Fig. 1)
-
Carefully remove the fixture from the carton and check that all parts are included as shown in the illustration.
-
Shut off the power at the fuse box or circuit breaker. If necessary, remove the old fixture including the mounting hardware.
-
Attach the circular strap (A) over the outlet box using the mounting screws (B) (Size: #8-32N*L0.5”), the side of the circular strap (A) marked “GND” must face out.
-
Thread the two studs (C) partway into the circular strap (A).
CONNECTING THE WIRES (Fig. 2) -
At this point, connect the electrical wires as shown in Figure 2, making sure that all wire connectors are secured. If your outlet box has a ground wire (green or bare copper), connect the fixture’s ground wire to it and secure it with the wire connectors, otherwise, connect the fixture’s ground wire directly to the crossbar using the green screw provided. After the wires are connected, tuck them carefully into the ceiling junction box.
COMPLETING THE INSTALLATION (Fig. 1) -
Place the backplate (E) over the two studs (C) through the holes, then secure the backplate (E) against the wall with the two cap nuts (D).
-
Install the light bulb(s) (not included) in accordance with the fixture’s specifications. (DO NOT EXCEED THE MAXIMUM WATTAGE RATING!!) (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!).
-
Slide the glass (F) onto the backplate (E) and set it into place.
Your installation is now complete. Return power to the junction box and test the fixture.
Note:
The illustration (Fig. 1) in this manual is for installation purposes only. It
may or may not be identical to the fixture purchased.
- MIN 90℃ SUPPLY CONDUCTORS.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>