FIRMTECH FBL601BC Bluetooth Low Energy Embedded Module User Guide
- June 3, 2024
- FIRMTECH
Table of Contents
FIRMTECH FBL601BC Bluetooth Low Energy Embedded Module
Revision History
| Revision | Date | Change Descriptions |
|---|---|---|
| Ver 1.0 | 2022-09-15 | – Write a draft |
(C) Copyright FIRMTECH Co., Ltd. 2005
All rights reserved
The products and operation descriptions contained herein shall be protected by
copyright law.
Any part or whole of products or operation description shall not be copied,
reproduced, translated, nor transformed into readable form by electronic
device or machines, without prior consent in writing by FIRMTECH Co., Ltd.
There might be some misprinting or technical faults in the products and
operation description which are subject to change without prior notice.
What is Bluetooth?
Features of Bluetooth
- Objectives of Bluetooth : To Realize Wireless Communication for Short Distance with Low Power Consumption, High Reliability, and Low Cost.
- Frequency in Use: To Use ISM(Industrial, Scientific, Medical) Band which does not require any permission to use.
- 2.400 – 2.4835 GHz, 79 channels
- 2.465 – 2.4835 GHz, 23 channels (in France)
- Transmission Rate : 1Mbps ~ 3Mbps
- Transmission Output : 1mW (10m, Class2), 100mW (100m Class1)
- Network Configuration : Configured with Master and Slave relation. A Bluetooth unit shall allow simultaneous connections up to 7 devices (in case of ACL).
- Reliability : To Guarantee stable wireless communication even under severe noisy environment through adopting the technique of FHSS
- (Frequency Hopping Spread Spectrum).
Operation of Bluetooth
<Feature 1-1 Bluetooth Operation>
- Bluetooth operates based on the connection between “Master” and “Slave”.
- Masters are simply supposed to do “Inquiry” and “Page”. Slaves are supposed to do “Inquiry Scan” and “Page Scan”.
- If a Master finds a Slave and so “inquiry” is successful, a Slave responds to the Master with its information.
Interconnection between the Master and the Slave is achieved only if the information from the Slave is corresponded with the Master, and the Slave sends data to the Master.
Product Overview
Major Features of FBL601BC_serial
- Bluetooth Specification 5.2 Low Energy Support
- Easily Applicable to the Product with 8 Pins Header Type
- Support AT Command, and capable to control FBL601BC_serial by using AT Command
- UART can be used as an interface
We request the new users of FBL601BC_serial to read the information on this description carefully before they start to use the products.
Product Components
FBL601BC_serial
| MODEL | PICTURE | Q’TY (EA) |
|---|
FBL601BC_serial
(On-board Chip Antenna)
| 
| 1
<Table 3-1 Basic Components of FBL601BC_serial >
Interface Board (Option)
| MODEL | PICTURE | Q’TY (EA) |
|---|---|---|
| Interface Board | **** | 1 |
<Table 3-2 Components of Interface Board >
If you find any of above components is defective, or not included in the package, please contact the seller you purchased.
FBL601BC_serial Appearance
FBL601BC_serial Dimension
[Top View]
[Side View]
<Figure 4-1 FBL601BC_serial Dimension>
FBL601BC_serial PIN Assign
<Figure 4-2 FBL601BC_serial PIN Assign>
| NO | Name of Signal | Features | I / O | Level |
|---|---|---|---|---|
| 1 | GND | Ground | ||
| 2 | VCC | DC 3.3V | ||
| 3 | STATUS | Operation Status | Output | TTL |
| 4 | FASET | |||
| CONFIG_SELECT | Factory Reset | |||
| Configuration Select | Input | TTL | ||
| 5 | Power Save Control | Power Save On/Off Control | Input | TTL |
| 6 | NC | No Connect | – | – |
| 7 | TXD | Transfer Data (Data out) | Output | TTL |
| 8 | RXD | Received Data (Data in) | Input | TTL |
< Table 4-1 Pin Description>
-
STATUS port
To be used to monitor the status of FBL601BC_serial
It keeps LOW (0V) when the Bluetooth wireless section is connected smoothly and both devices can communicate
In standby mode for connection with Bluetooth, or connection trial, or searching for around Bluetooth device will repeat LOW and HIGH. -
FA_SET / CONFIG_SELECT
If you want to enter the configuration mode, turn on the power to the module while inputting LOW Signal (0V) to Configuration Select (No. 4 pin).
If you want to change to the factory default value, enter the LOW Signal (0V) for more than 5 seconds into the Factory Reset (Pin No. 4) after entering the configuration mode and all setting values will be changed to the original purchase status. -
Power Save Control Port
Select FBL601BC_serial’s Power Save ON/OFF Control When high is applied it operates as Power Save On When low is applied, it operates as power save off.
5 Interface (Pin Connection)
< Figure 5-1 Pin Connection
Control>
Interface Board (Jig Board)
<Figure 6-1 Interface Board>
| No. | Title | Description |
|---|---|---|
| 1 | UART communication & power port | UART |
communication interface terminal for PC connection
5V power input terminal
2| Power ON/OFF Switch| Interface Board Power On/Off Switch
3| STATUS LED| USB LED : USB port status LED POWER LED
: 3.3V power supply LED STATUS LED : Status confirmation LED RX
LED : UART input confirmation LED
TX LED : UART Output confirmation LED
4| Configuration Select Switch| Switch for enter the configuration
mode
The configuration entry mode method is as follows.
- Hold CONFIG switch and power on..
- Enter the configuration mode completed
Factory Reset Switch| Factory initialization switch
The Factory initialization is as follows.
- Enter the configuration mode
- After entering configuration mode, press the FASET switch Hold for 5 seconds.
- Factory initialization completed
5| Connection connector| FBL601BC_serial Connection connector
< Table 6-1 PC Interface Board>
Specification of FBL601BC_serial
| No. | Part | Specification |
|---|---|---|
| 1 | Bluetooth Spec. | Bluetooth Specification 5.2 Low Energy Support |
| 2 | Communication distance | 10 M |
| 3 | Frequency Range | 2402 ~ 2480 MHz ISM Band |
| 4 | Sensitivity | -79dBm (Typical) |
| 5 | Transmit Power | 0dBm(Typical) |
| 6 | Size | 15.50mm x 18.50 mm x 12.34mm |
| 7 | Support Bluetooth Profile | GATT Service |
| 8 | Input Power | 3.3V |
| 9 | Current Consumption | Peripheral |
| Central | 4.5mA(Max : Scanning) | |
| 10 | Temperature | Operating |
| Limit Operating | -40℃ ~ 85℃ | |
| 11 | Communication Speed | 9,600bps – 115,200bps |
| 12 | Antenna | Chip Antenna |
| 13 | Interface | UART (TTL Level) |
< Table 7-1 FBL601BC_serial Specification>
Current Consumption
| Status | Current Consumption (mA) |
|---|---|
| MIN | MAX |
| Ready | 1.79 |
| Advertising | 1.86 |
| Connection | 1.92 |
< Table 8-1 Peripheral Current Consumption of FBL601BC_serial>
| Status | Current Consumption (mA) |
|---|---|
| MIN | MAX |
| Ready | 1.87 |
| Scanning | 4.25 |
| Connection | 1.95 |
< Table 8-2 Central Current Consumption of FBL601BC_serial> TEST CONDITIONS
Baud Rate : 9600 bps, Input Voltage : DC 3.3V
The power consumption will change depending on transmission speed and volume
of data.
Preliminary Product Components
The preliminary value of product is set as on the <Table 9-1>.
Please be sure of basic set value and so on before using the product.
| Type | Set Value |
|---|---|
| Device Name | FBL601(XXXXXX) |
| Uart (baud rate-data bit-parity bit-stop bit) | 9600-8-N-1 |
| ROLE | Peripheral |
| Advertising Interval | 100ms |
| Connection Interval | 12ms |
<Table 9-1 Preliminary Configuration Setting Value for FBL601BC_serial>
FBL601BC_serial can change the setting value by using AT command of Bluetooth setting.
FCC MODULAR APPROVAL INFORMATION EXAMPLES for Manual
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20 cm between the radiator & your body.
OEM INTEGRATION INSTRUCTIONS:
This device is intended only for OEM integrators under the following
conditions:
The module must be installed in the host equipment such that 20 cm
is maintained between the antenna and users, and the transmitter
module may not be co‐located with any other transmitter or antenna.
The module shall be only used with the internal on‐board antenna
that has been originally tested and certified with this module.
External antennas are not supported. As long as these 3 conditions
above are met, further transmitter test will not be required.
However, the OEM integrator is still responsible for testing their
end‐product for any additional compliance requirements required with this
module installed (for example, digital device emissions, PC peripheral
requirements, etc.). The end‐product may need Verification testing,
Declaration of Conformity testing, a Permissive Class II Change or new
Certification. Please involve a FCC certification specialist in order to
determine what will be exactly applicable for the end‐product.
Validity of using the module certification:
In the event that these conditions cannot be met (for example
certain laptop configurations or co‐location with another transmitter),
then the FCC authorization for this module in combination with the host
equipment is no longer considered valid and the FCC ID of the module cannot be
used on the final product. In these circumstances, the OEM integrator
will be responsible for re‐evaluating the end product (including the
transmitter) and obtaining a separate FCC authorization. In such
cases, please involve a FCC certification specialist in order to
determine if a Permissive Class II Change or new Certification is
required.
Upgrade Firmware:
The software provided for firmware upgrade will not be capable to affect any
RF parameters as certified for the FCC for this module, in order to prevent
compliance issues.
Information that must be placed in the end user manual:
The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF module in the user’s manual of the
end product which integrates this module. The end user manual shall include
all required regulatory information/warning as show in this manual.
End product labeling:
Documents / Resources
|
FIRMTECH FBL601BC Bluetooth Low Energy Embedded
Module
[pdf] User Guide
FBL601BC-SERI, FBL601BCSERI, U8D-FBL601BC-SERI, U8DFBL601BCSERI, FBL601BC,
Bluetooth Low Energy Embedded Module, Low Energy Embedded Module, Embedded
Module
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>