OSTRO Furniture AOF-RSB04 Riley Sideboard Light Oak Instruction Manual
- June 9, 2024
- OSTRO Furniture
Table of Contents
Sideboard
Assembly Instructions
Model Number: A0E-RSB04
Assembly Requirements
Quickfit/Cam Lock Guide To use the quickfit/cam lock, first insert the
quickfit into the panel. The “shoulder” of the quickfit should be flush
against the panel, as shown in (a). When inserting the cam lock, ensure the
orientation is correct, as shown, so that it aligns properly with the
quickfrt, as shown in (b) and (c).
Once the panels have been connected, tighten the cam lock with a screwdriver
(d).
Important Safety Information
IMPORTANT: Please read this manual carefully, and keep it for future reference.
-
This piece of furniture is intended for use in domestic environments. It is not suitable for commercial, industrial or trade use. Do not use it for any other purpose, and only use it as described in this manual.
-
Assembly to be carried out by a competent adult only. Please check all parts and hardware are available and undamaged before use.
-
During assembly children should be kept away from the product due to possible risk of injury.
-
Do not use this item if any components are missing or damaged.
-
Regularly check all fastenings to ensure that they properly tightened.
-
Do not use the unit outdoors. It is for indoor use only.
-
Keep away from fire and heat sources.
-
Be aware of the risk of open fires and other sources of strong heat in the vicinity of the product.
-
Do not use this product in a bathroom or laundry, or where it can be splashed with water.
-
This item of furniture is not intended to be assembled by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge.
-
Handle this product with care. Do not shake the product vigorously or drop it from an elevation. Doing so will damage the product or shorten its lifespan. Do not sit or stand on the item of furniture, which may lead to potential injury. Do not press hard on top of the unit or place very heavy things on top of it.
-
Always place the product on a dry, stable, level and horizontal surface. Never place it on an inclined or uneven surface.
-
Do not locate the item of furniture near appliances that get hot during use, such as heaters, ovens or fireplaces. Avoid long-term exposure to direct sunshine.
-
We accept no responsibility for any eventual injury or damage caused by improper installation, misuse or noncompliance with the instructions.
-
These instructions are not intended to cover every possible condition and situation. As with any product, common sense and caution are therefore always recommended when assembling, using and maintaining the item of furniture.
-
Do not over-tighten fixtures.
-
Power tools are not recommended for assembly.
-
This item of furniture is heavy – take care when moving it. Multiple people or a mechanical aid may be required.
-
CAUTION: Do not allow children to climb on this furniture – it may topple over and badly injure a child. Do not place toys or other items that may appeal to a child on top of this furniture item.
-
CAUTION: Attachment of this item of furniture must be attached to an appropriate structural component of the building using suitable means, as advised by a qualified tradesperson, is strongly recommended.
Care and Maintenance:
- Ensure that all fastenings and fixtures have been sufficiently tightened. You may need to re-tighten periodically, as necessary.
- To clean, wipe clean with a damp cloth, before drying thoroughly.
- Do not place hot or wet items on the surface.
- Do not drag or pull your furniture.
Responsible disposal
Packaging materials are recyclable. Please dispose of them responsibly for
recycling.
At the end of its working life, do not throw this item of furniture out with
your household waste. Please dispose of this product at your local community’s
waste collection/ recycling centre. Observe any local regulations regarding
the disposal of this type of product.
NOTE: Due to continued product improvement, images and illustrations in
this manual may vary slightly from the product purchased. All images in this
set of assembly instructions are for reference purposes only. Parts are not
necessarily pictured to scale.
ASSEMBLY INSTRUCTIONS
Before you begin, please follow assembly instructions carefully, then follow
them step by step.
Read instruction carefully. See Furniture Parts list and Hardware List for
guidance. Be sure you have all parts before you start assembling. Place and
assemble furniture on a clean flat soft surface , such as carpet or rug to
pervent being scratched.
PART LIST | QTY |
---|---|
1 | TOP PANEL |
2 | BOTTOM PANEL |
3 | SIDE PANEL (L) |
4 | SIDE PANEL (R) |
5 | CENTER PANEL (L) |
6 | CENTER PANEL (R) |
7 | MIDDLE PANEL |
8 | BACK BONE |
9 | BACK PANEL |
10 | SHELF PANEL |
11 | DRAWER FRONT |
12 | DRAWER BACK |
13 | DRAWER SIDE (L) |
14 | DRAWER SIDE (R) |
15 | DRAWER BOTTOM |
16 | DRAWER BONE |
17 | DOOR PANEL (L) |
18 | DOOR PANEL (R) |
19 | CABINET LEG |
20 | CENTER LEG |
Reminder.
Please ensure that all surfaces and edges with colours/laminations are facing
forward/outward.
STEP 1
– Insert hardware Al onto panel (16). (Repeat 6 times.)
– Insert hardware A2 onto panel (1). (Repeat 12 times.)| STEP 2
– Insert hardware Al onto panel (3), (4) and (5). (Repeat 6 times.)
– Insert hardware A2 onto panel (3) and (5). (Repeat 2 times.)
– Insert hardware B onto panel (3), (4) and (5). (Repeat 12 times.)
---|---
• Ensure the arrows on hardware Al point
towards mounting positions.| • Ensure the arrows on hardware
Al point towards mounting positions.
STEP 3
– Insert hardware Al onto panel (6), (7) and (8). (Repeat 8 times.)
– Insert hardware B onto panel (6) and (7). (Repeat 6 times.)| STEP 4
Insert hardware A2 onto panel (11) and (12). (Repeat 12 times.)
• Ensure the arrows on hardware Al point
towards mounting positions.|
STEP 5
– Insert hardware Al onto panel (13) and (14). (Repeat 6 times.)
– Insert hardware B onto panel (13) and (14). (Repeat 6 times.)| STEP 6
Px hardware 01 (1./R) into panel (3) and (5) with hardware E. (Repeat 3 times
for each hardware.)
• Ensure the arrows on hardware Al point
towards mounting positions.|
STEP 7
– Attach panel (7) to panel (3) and (5).
– Insert all hardware AS Into Al.
– Rotate al Al untl tight.
– Apply A3 onto all Al. (Repeat 2 times.)| STEP 8
– Attach panel (1) to panel (3), (4), (5) and (6).
– Insert al hardware A2 into Al.
– Rotate all Al until tight.
– Apply AS onto all Al. (Repeat 8 times.)
In this step hardware Al, AS and B are pre-inserted.| In this step hardware Al, AS and B are pre-inserted.
STEP 9
Insert the panel (9) along the slot. (Repeat 1 times.)| STEP 10
– Attach panel (8) to panel (1).
– Insert all hardware A2 Into Al.
– Rotate all Al until tight.
– Apply A3 onto all Al. (Repeat 4 times.)
| In this step hardware Al, A2 and B are
pm-Inserted.
STEP 11
Connect part (20) to panel (2) by using hardware G. (Repeat 2 times.)| STEP 12
Connect panel (2) to panel (3), (4), (5), (6) and (8) by using hardware C and
D. (Repeat 12 times.)
| In this step
hardware B are pre-inserted.
STEP 13
Assemble part 19 into panel (2) by using hardware D, J, K and L. (Repeat 2
times for each Leg.)| STEP 14
Hit hardware I into bottom of part (19) and (20). (Repeat 5 times.)
|
STEP 15
Insert hardware M into mounting positions on panel (4), (5) and (6) by hand.
(Repeat 16 times.)| STEP 16
Assemble the panel (10) into between panel (4) and (6). (Repeat 2 times.)
Assemble the panel (10) into between panel (5) and (6). (Repeat 2 times.)
| • In this step hardware M are pre-inserted.
STEP 17
– Fix hardware N onto panel (17) and (18) by using hardware E. (Repeat 2 times
for each hardware.)
– Fix hardware P onto panel (11), (17) and (18) by using hardware F. (Repeat 1
times for each hardware.)| STEP 18
Assemble panel (12) to panel (13) and (14) by using hardware H. (Repeat 12
times.)
| • In this step
only show one of the drawers.
STEP 19
Insert the panel (15) along the slot. (Repeat 3 times.) In this step only
show one of the drawers.| STEP 20
– Attach panel (16) to panel (12).
– Insert all hardware A2 Into Al.
– Rotate all Al until tight.
– Apply A3 onto all Al. (Repeat 3 times.)
• In this step only show one of the drawers.
| In this step hardware Al, A2 and B are
pre-inserted.
STEP 21
– Attach panel (11) to panel (13), (14) and (16).
– Insert all hardware A2 Into Al.
– Rotate all Al until tight.
– Apply A3 onto all Al. (Repeat 9 times.)
• In this step only show one of the drawers.| STEP 22
Assemble hardware 02 (L/R) to panel (13) and (14) by using hardware E. (Repeat
3 times for each hardware.)
• In this step only show one of the drawers.
• In this step hardware Al, A2 and II
are pre-Inserted.| Hardware 02 (L/R) shall be leaning
against panel (11) when assembling.
STEP 23 Put as the drawer in place along the drawer slides.| STEP 24
– Fix hardware N Into panel (4) and (5) by using hardware E. (Repeat 4 times
for each hardware.)
-lighten or loosen the screw to adjust position of panel (17) and (18). (Do only when needed.)
| In this step hardware N have been
assembled in panel (17) and (18).
STEP 25
Assemble hardware 01 into panel (1) by using hardware 02. (Repeat 2 times.)|
STEP 26
– Mark and use the power dnil to drill a hole on the wall.
– Hit hardware 03 into the wall. (Repeat 2 times.)
|
STEP 27
– Assemble hardware 01 to 03 by using hardware Q4. (Repeat 2 times.)| STEP
28
– Connect both of the hardware Q1 by using hardware 05. -lighten the hardware
Q5. (Repeat 2 times.)
|
* Maximum recommended weight is 25kg on the top, 15kg for the cupboards and 5kg per drawer
Warranty returns
Should you for any reason need to return this product for a warranty claim,
make sure to include all accessories with the product.
Product does not work?
If you encounter problems with this product, or if it fails to perform to your
expectations, make sure to contact our After Sales Support Centre on (AU) 1300
886 649 or (NZ) 0800 836 761 for advice.
For an electronic copy of this manual, please contact our after sales support
centre.
Distributed by Tempo (Aust) Pty Ltd ABN 70 106 100 252
PO BOX 132, Frenchs Forest NSW 1640, Australia
Customer Helpline: (AU) 1300 886 649 (NZ) 0800 836 761 Web Support:
tempo.org/support
IM Version No: V1.0
Issue: August 2022
AFTER SALES SUPPORT (AU) 1300 886 649 (NZ) 0800 836 761