MINKA LAVERY 4058732 60W 2-Light Bath Light Instruction Manual

: June 13, 2024
: MINKA LAVERY

Table of Contents

MINKA LAVERY 4058732 60W 2-Light Bath Light
Product Information
Product Usage Instructions
INSTALLATION INSTRUCTIONS
Read User Manual Online (PDF format)
Download This Manual (PDF format)

MINKA LAVERY 4058732 60W 2-Light Bath Light

MINKA-LAVERY-4058732-60W-2-Light-Bath-Light-product

Product Information

Product Name: Item#6522
Date of Manufacture: 08/23/2012
Installation Instructions: Read and save these instructions

Product Usage Instructions

Mounting the Fixture

Refer to Fig. 1 for visual aid.

Remove the fixture from the carton and ensure all parts are included.
Shut off power at the circuit breaker and remove the old fixture, including the mounting hardware.
Position the Mounting Plate (B) on the wall and mark the location of two mounting holes. Drill the holes on the wall andinsert the Plastic Anchors (K).
Attach the Mounting Plate (B) to the Outlet box (A) in the wall using the two screws (C). Ensure that the side of the mountingplate marked GND faces out.
Place the Wood Screws (L) through the holes into the Plastic Anchors (K) to secure the Mounting Plate (B).

Connecting the Wires

Refer to Fig. 2 for wire connections.

Connect the electrical wires as shown in Fig. 2, ensuring that all wire connectors are secured. If your outlet has a ground wire (green or bare copper), connect the fixture’s Ground Wire to it. Otherwise, connect the fixture’s Ground Wire directly to the mounting plate or Reinforcement Plate using the Green Screw provided. After connecting the wires, carefully tuck them into the outlet box.

Finishing the Installation

Refer to Fig. 1 for visual aid.

Place the Fixture Body (F) over the Mounting Plate (B) and fasten it with Screws (D) using the Allen Wrench (E) provided.
Install light bulbs (G) (not included) according to the fixture’s specifications. Do not exceed the maximum wattagerating.
While holding the Glass panel (H) towards the Fixture Body (F), insert the Plastic Washer (N) and Cast part (I) between the end of the glass panel and Holder (M), then secure it with the Finial (J).

Your installation is now complete. Restore power to the outlet box and test the fixture.

Note: The illustration in Fig. 1 is for installation purposes only and may or may not be identical to the fixture purchased.

Manufacturer’s Reference: LA-1623E

INSTALLATION INSTRUCTIONS

Item#6522 （New. 08/23/2012）
READ AND SAVE THESE INSTRUCTIONS

WARNING! SHUT POWER OF F AT FUSE OR CIRCUI T BRE AKER.
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.

MOUNTING THE FIXTURE (Fig. 1 )

Carefully remove the fixture from the carton and check that all parts are included as shown in theillustration.
Shut off power at the circuit breaker and remove old fixture, including the mounting hardware.
Position Mounting Plate (B) on the wall, and mark location of two mounting holes. Drill the hole on the wall. Insert the Plastic Anchors (K) into the wall.
Attach the Mounting Plate (B) to the Outlet box (A) in the wall using the two screws (C). The side of the mounting plate marked “GND” must face out.
Place theWood Screws (L) through the hole into the Plastic Anchors (K) secure the Mounting Plate (B).
CONNECTING THE WIRES (Fig. 2)
At this point, connect the electrical wires as shown in Fig. 2, making sure that all wire connectors are secured. If your outlet has a ground wire (green or bare copper), connect the fixture’s Ground Wire to it. Otherwise, connect the fixture’s Ground Wire directly to the mounting plate or Reinforcement Plate using the Green Screw provided. After wires are connected, tuck them carefully into the outlet box.
FINISHING THE INSTALLATION (Fig. 1)
Place Fixture Body (F) over Mounting Plate (B), fasten with Screws (D) by using Allen Wrench (E) provided.
Install light bulbs (G) (not included) in accordance with the fixture’s specifications. (DO NOT EXCEED THE MAXIMUM WATTAGE RATING!) (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!)
While holding the Glass panel (H) toward the Fixture body (F), insert the Plastic Washer (N) and Cast part (I) between end of glass panel and Holder (M), then secure with the Finial (J).