Minka Lavery 4462 60 W 4 in 2 Light Medium Wall Sconce Instruction Manual
- June 13, 2024
- MINKA LAVERY
Table of Contents
Minka Lavery 4462 60 W 4 in 2 Light Medium Wall Sconce
Product Information
- Product Name: Item#4462
- Date of Manufacture: January 4, 2012
Installation Instructions
- WARNING: Shut off power at the fuse or circuit breaker before installation.
- AVERTISSEMENT: Couper le courant au niveau des fusibles ou du disjoncteur avant l’installation.
Mounting the Fixture (Fig.1)
-
Shut off the power at the circuit breaker and remove the old fixture, including the mounting hardware.
-
Carefully unpack your new fixture and lay out all the parts on a clear area. Take care not to lose any small parts necessary for installation.
-
Attach the mounting plate (A) to the outlet box using the mounting screws (B) (Size: #8-32N*L0.5). The side of the mounting plate marked GND must face out.
Connecting the Wires (Fig. 2) -
At this point, connect the electrical wires as shown in figure 2, making sure that all wire connectors are secured. If your outlet box has a ground wire (green or bare copper), connect the fixture’s ground wire to it and secure with the wire connectors. Otherwise, connect the fixture’s ground wire directly to the mounting plate using the green screw provided. After wires are connected, tuck them carefully into the ceiling junction box.
Finishing the Installation (Fig. 1) -
Place the Backplate (G) over the mounting plate (A), and secure it with screws (C).
-
Install the light bulb(s) (E) (not included) in accordance with the fixture’s specification. DO NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!)
-
Place the glass (F) over the socket and twist to secure it to the fixture.
Note: Illustration (Fig.1) on this manual is for installation purposes only. It may or may not be identical to the fixture purchased.
Product Usage Instructions
| Fixture Wires | Black or Smooth |
|---|---|
| Fixture Wires | White or Ribbed |
| Fixture Wires | Bare Copper (Ground) |
| House Wires | Black (Hot) |
| House Wires | White (Neutral) |
| House Wires | Green (Ground) |
Your installation is now complete. Return power to the junction box and test the fixture.
READ AND SAVE THESE INSTRUCTIONS
WARNING! SHUT POWER OF F AT FUS E OR CIRCUI T BRE AKE R.
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU
DISJONCTEUR.
MOUNTING THE FIXTURE (Fig.1)
- Shut off the power at the circuit breaker and remove old fixture, including the mounting hardware.
- Carefully unpack your new fixture and lay out all the parts on a clear area. Take care not to lose any small parts necessary for installation.
- Attach the mounting plate (A) to the outlet box using the mounting screws (B) (Size: #8-32N*L0.5”). The side of the mounting plate marked “GND” must face out.
CONNECTING THE WIRES (Fig. 2)
At this point, connect the electrical wires as shown in figure 2, making sure that all wire connectors are secured. If your outlet box has a ground wire (green or bare copper), connect the fixture’s ground wire to it and secure with the wire connectors, otherwise, connect the fixture’s ground wire directly to the Mounting plate using the green screw provided. After wires are connected, tuck them carefully into the ceiling junction box.
FINISHING THE INSTALLATION (Fig. 1)
Place the Backplate (G) over the mounting plate (A), and secure it with screws (C). 6. Install the light bulb(s) (E) (not included) in accordance with the fixture’s specification. (DO NOT EXCEED THE MAXIMUM WATTAGE RATING!!) (NE PAS DEPASSER LA PUISSANCE NOMINALEMAXIMALE!).
- Place the glass (F) over the socket and twist to secure it to the fixture.
- Your installation is now complete. Return power to the junction box and test the fixture.
- Note: Illustration (Fig.1) on this manual is for installation purposes only. It may or may not be identical to the fixture purchased
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>