MINKA LAVERY 6961 9 Inch 100W 1-Light Bath Light Instruction Manual
- June 13, 2024
- MINKA LAVERY
Table of Contents
MINKA LAVERY 6961 9 Inch 100W 1-Light Bath Light
Product Information
The product is a fixture with the model number 6961. It is designed for installation in a wall-mounted outlet box. The fixture includes a mounting strap, nipple, lock nut, glass shade, cushion ring, socket ring, finial, and a back plate. It is important to note that the fixture should be installed with caution and the power supply should be shut off before proceeding with the installation.
Product Usage Instructions
- Before starting the installation, shut off the power supply at the fuse box or circuit breaker.
- If there is an existing fixture, remove it from the wall along with the mounting hardware.
- Take out the new fixture from the carton and ensure that all parts are included.
- Thread the nipple (C) into the mounting strap (A).
- Place the washer (F) and lock nut (E) over the nipple protruding through the mounting strap and securely tighten the lock nut onto the nipple.
- Attach the mounting strap (A) to the outlet box using the provided outlet box screws (B). Ensure that the side of the mounting plate marked GND faces outwards.
- Follow the wiring instructions carefully as shown in Fig.2.
- Attach the fixture back plate (L) over the mounting strap (A) and allow the nipple (C) to protrude through the center hole of the back plate. Secure it with the finial (K).
- Place the glass shade (I) and cushion ring (H) over the socket (J) and secure them with the socket ring (G).
- Install a bulb according to the fixture’s specifications. Make sure not to exceed the maximum wattage rating.
- Connect the electrical wires as shown in Fig.2. Ensure that all wire connectors are secured. If your outlet box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting strap using the provided green screw.
- Tuck the wire connections neatly into the wall junction box.
- Once the installation is complete, restore power to the outlet box and test the fixture.
INSTALLATION INSTRUCTIONS
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
MOUNTING THE FIXTURE
- Shut off the power supply at the fuse box or circuit breaker. If necessary, remove the old fixture from wall including the mounting hardware.
- Carefully remove the new fixture from the carton and check that all parts are included as shown in the illustration.
- Thread the nipple (C) into the mounting strap (A).
- Place the washer (F) and lock nut (E) over the nipple protruding through the mounting strap and thread lock nut (E) tightly onto nipple (C).
- Attach the mounting strap (A) to the outlet box using the outlet box screws (B). The side of the mounting plate marked “GND” must face out.
- Follow the wiring instructions carefully (See Fig.2).
- Attach the fixture back plate (L) over the mounting strap (A) allowing the nipple (C) to protrude through the center hole of the back plate (L). Then secure with finial (K).
- Place the glass shade (I) and cushion ring (H) over the socket (J) and secure with socket ring (G).
- Install the bulb in accordance with fixture’s specifications. (DO NOT EXCEED THE MAXIMUM WATTAGE RATING!) (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!).
CONNECTING THE WIRES (See fig. 2)
- At this point, connect the electrical wires as shown in Fig. 2, making sure that all wire connectors are secured. If your outlet box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting strap using the green screw provided.
- Tuck the wire connections neatly into the wall junction box.
Your installation is now complete. Return power to the outlet box and test the fixture.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>