MINKA LAVERY 2921-77-L 14W 1-Light Medium E-26 Base Bath Light Instruction Manual

MINKA LAVERY 2921-77-L 14W 1-Light Medium E-26 Base Bath Light

Product Information

The product is a LED Wall Mount Fixture with the model number 2921-77-L. It is designed to provide lighting in various indoor spaces. The fixture is dimmable with C-L (CFL & LED) type and Incandescent/Halogen type dimmers. The installation of this fixture should be done by a qualified electrician to ensure proper wiring and installation.

Product Usage Instructions

Before starting the installation process, it is important to shut off the power at the fuse or circuit breaker box.

Mounting the Fixture

1. Shut off power at the fuse box or circuit breaker box.
2. Proceed with the installation process as shown in Figure 1.
3. Once the installation is complete, restore power to the junction box and test the fixture.

Note : When handling the fixture, avoid applying pressure to the LEDs. Hold the fixture by the base or fixture body only.

Replacing LED Module

The LED module can be replaced by a qualified electrician without cutting the wires and without damaging the decorative element to which the fixture is attached. Follow the steps below:

1. Turn off power at the fuse box circuit breaker before replacing the LED module.
2. To remove the fixture from the wall:
   • Loosen screws (D) and remove the wire connectors.
   • Place the fixture on a clear flat surface.
3. To remove the glass shade (L):
   • Loosen screw (Q).
4. To remove the end caps (H) and glass shade (K):
   • Loosen screws (G).
5. To remove the LED module (I):
   • Loosen screws (J), screws (M), and wire fastener (N).
   • Carefully remove the LED module.
6. Reverse the steps above to install the new LED module.

Note : The LED module should be provided by a specified supplier.

WARNING! SHUT POWER OF F AT FUS E OR CIRCUI T BREAKER.

INSTALLATION INSTRUCTIONS

MOUNTING THE FIXTURE (Fig. 1)

1. Shut off power at the fuse box or circuit breaker box. If necessary, remove the existing fixture and its mounting hardware.

2. Carefully remove the new fixture from the carton and check that all parts are included as shown in the illustration.

3. Attach the mounting plate (A) to the junction box using junction box screw (B) (Size: 8-32*1/2’’L). The side of the mounting plate marked “GND” must face out.
   CONNECTION THE WIRES (Fig. 2)

4. Connect the electrical wires as shown in Fig.2, making sure that all wire connectors are secured. If your outlet has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate using the green screw provided. Tuck the wire connections neatly into the junction box.
   FINISHING THE INSTALLATION (Fig. 1)

5. Align Fixture (E) onto mounting plate (A) and secure with screws (D).

6. Place glass shade (L) inside the fixture (E), and secure with screw (Q) steel washer (P) and plastic washer (O). Your installation is now complete. Return power to the junction box and test the fixture.
   CAUTION /ATTENTION : When handling the fixture, do not apply pressure to the LEDs. Hold the fixture by the base or fixture body (E) only.

Replacing LED module

The LED module can be replaced by a qualified electrician without cutting the wires and without damaging the decorative element to which the fixture is attached. See installation steps for more details (Fig 3.)
Warning : Turn off power at the fuse box circuit breaker before replacing LED module.

• To remove the fixture from the wall: loosen screws (D), and remove the wire connectors. Then place the fixture on a clear flat surface.
• Loosen screw (Q) to remove the glass shade (L).
  • Loosen screws (G) to remove end caps (H) and glass shade (K).
• Loosen screws (J), screws (M), wire fastener (N), and then carefully remove the LED module (I).
• Reverse steps a-c for installing the new LED module.
  Note : The LED module should be provided by a specified supplier.

IMPORTANT : Fixture should be installed by a qualified electrician to ensure proper wiring and installation.
Dimmable with C-L (CFL & LED) type and Incandescent/Halogen type dimmers

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>