aLora PD321712PN Marni String Pendant Installation Guide

June 13, 2024
aLora

aLora-logo

aLora PD321712PN Marni String Pendant

aLora-PD321712PN-Marni-String-Pendant-product

Product Information

Warnings and Cautions
Before proceeding with the assembly and installation of the pendant, please read and understand the following warnings and cautions:

  • Ensure that the fixture is removed from its original package.
  • Make sure to handle the fixture and its components with care to avoid damage.
  • Do not attempt to install the pendant without following the provided instructions.
  • Ensure that proper electrical connections are made as instructed to avoid any electrical hazards.
  • Consult a professional electrician if you are unsure about any step or if you encounter any difficulties during the installation process.

Assembly Instructions
Step 1:
Remove Fixture from its Original Package Take the pendant fixture out of its original package.

Step 2: Separate Mounting Plate from Canopy Remove the canopy screws to separate the mounting plate from the canopy.

Step 3: Attach Mounting Plate to Electrical Junction Box Use the provided junction box screws to attach the mounting plate to the electrical junction box. Refer to Illustration 1 for optional mounting option using a non-powered backplate and junction box.

Step 4: Make Proper Electrical Connections
Connect the wires as follows using the wire nuts provided in the hardware package:

  • Hot (Black) wire to the hot L connection
  • Neutral (White) wire to the neutral N connection
  • Ground (Green) wire to the GND connection
  • Dim + (Purple) wire to the Dim + connection (optional)
  • Dim – (Gray) wire to the Dim – connection (optional)

Step 5: Attach Canopy to Mounting Plate
Secure the canopy to the mounting plate using the canopy screws.

Step 6: Horizontal Orientation Option
If you prefer a horizontal orientation for your pendant, follow these steps:

  • Secure the non-powered backplate to the mounting surface using the butterfly clips and screws.
  • Attach the non-powered decorative cover to the non-powered backplate.
  • Attach the pivot to the decorative cover and secure it with the decorative ring by threading it clockwise.
  • Align the hole in the pivot with the fixture end and secure it with the provided screw.

Step 7: Vertical Orientation Option
If you prefer a vertical orientation for your pendant, follow these steps:

  • Remove the fixture end and cut any excess wire.
  • Secure the bead end to the fixture by threading it clockwise.

Step 8: Remove Protective Paper
Remove any protective paper covering the pendant fixture.
Congratulations! You have successfully assembled and installed your pendant fixture. You are now ready to enjoy its illumination.

Note: If you have any further questions or need assistance, please contact our technical support at the provided phone number or email address.

Manufacturer Information:

  • Canada: 19054 28th Avenue Surrey – BC V3Z 6M3
  • USA: 3035 E. Lone Mountain Rd – Las Vegas, NV, 89081
  • Website: www.aloralighting.com

Safety Instruction

WARNINGS AND CAUTIONS

  • Make sure POWER is COMPLETELY OFF at the fuse box
  • Have your fixture installed by a qualified licensed electrician
  • Prepare everything in a clear area
  • Wear gloves at all times during this installation
  • Read instructions carefully before you start assembly
  • Keep this installation sheet for future reference

NOTICE

  • The important safeguards and instructions outlined in this sheet cannot cover  all possible conditions and situations that may occur. It must be understood that caution and certain care factors must be followed. These instructions are provided for your safety and we highly recommend that a licensed, trained electrician install this unit.

Please Note:

  • This Alora LED fixture comes with pre-wired LED module(s)
  • Unless instructed, Do Not touch any part of the LED module(s) as any unnecessary contact with the module could cause permanent damage
  • For dimming, an ELV (Electronic Low Voltage), TRIAC or 0-10V type of dimmer is required
  • 120-277V input

ASSEMBLY INSTRUCTIONS

  • Step 1
    Remove fixture from its original package.

  • Step 2
    Separate mounting plate (1c) from canopy (2a) by removing canopy screws (2b).

  • Step 3
    Attach mounting plate (1c) to electrical junction box (1a) using junction box screws provided (1e) in hardware package.

  • Step 4
    Make proper electrical connections (black to hot “L”, white to neutral “N”, green to “GND”, Dim + to purple, Dim- to gray) with wire nuts provided in hardware package.

  • Step 5
    Attach canopy (2a) to mounting plate (1c) with canopy screws (2b).

  • Step 6 (For Horizontal Orientation Option)
    Secure non-powered backplate (5b) to mounting surface by compressing butterfly clips (5a) through 3/8” holes in ceiling and then use screws (5c) to fasten. (See Illustration 1 for optional mounting option). Attach non-powered decorative cover (6a) to non-powered backplate (5b), followed by pivot (6b) and secure with decorative ring (6c) by threading clockwise. Align hole in pivot (6b) and fixture end (7a) and secure with screw (6d).

  • Step 7 (For Vertical Orientation Option)
    Remove fixture end (7a) and cut excess wire (See Illustration 2). Secure bead end (10a) to fixture by threading clockwise (See Illustration 3)

  • Step 8
    Remove protective paper.
    You are now ready to enjoy your fixture.

aLora-PD321712PN-Marni-String-Pendant- \(2\)

P: 1.855.855.8926
CANADA : 19054 28th Avenue Surrey – BC V3Z 6M3
USA : 3035 E. Lone Mountain Rd – Las Vegas, NV, 89081 www.aloralighting.com
20230619

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals