aLora LP348148 Edwin 40W LED Linear Pendant Installation Guide

June 13, 2024
aLora

aLora-logo

aLora LP348148 Edwin 40W LED Linear Pendant

aLora-LP348148-Edwin-40W-LED-Linear-Pendant-product

Product Information

Warnings and Cautions
Please Note:
This user manual contains important information regarding the installation and usage of the LP348148 Linear Pendant. It is crucial that you follow the instructions provided to ensure your safety. We strongly recommend that a licensed and trained electrician install this unit.

Assembly Instructions

  1. Step 1: Remove the fixture from its original package.
  2. Step 2: Separate the mounting plate (1c) from the canopy (2a) by removing the canopy screws (2b).
  3. Step 3: Attach the mounting plate (1c) to the electrical junction box (1a) using the junction box screws provided (1e) in the hardware package.
  4. Step 4: Secure the mounting plate (1c) to the mounting surface with anchors (1f) and screws (1g).
  5. Step 5: Determine the hanging height of the fixture by securing rods (2d) to the canopy (2a) and fixture body (3a) after feeding the fixture wires (LED+ and LED-) through the rods.
  6. Step 6: Make proper electrical connections between the LED and DC driver, LED- Negative, LED+ Positive using wire nuts provided. Refer to Illustration 1 and the diagram on the driver for guidance.
  7. Step 7: Make proper electrical connections (black to hot L, white to neutral N, ground to GND) with wire nuts provided in the hardware package. Place the driver (4a) inside the canopy (2a).
  8. Step 8: Secure the glass (3b) to the fixture body (3a) by threading it clockwise.
  9. Step 9: Attach the canopy (2a) to the mounting plate (1c) with the canopy screws (2b).

You are now ready to enjoy your LP348148 Linear Pendant.

Contact Information:

  • P: 1.855.855.8926
  • Canada: 19054 28th Avenue Surrey – BC V3Z 6M3
  • USA: 3035 E. Lone Mountain Rd – Las Vegas, NV, 89081
  • Website: www.aloralighting.com

Safety Instruction

WARNINGS AND CAUTIONS

  • Make sure POWER is COMPLETELY OFF at the fuse box
  • Have your fixture installed by a qualified licensed electrician
  • Prepare everything in a clear area
  • Wear gloves at all times during this installation
  • Read instructions carefully before you start assembly
  • Keep this installation sheet for future reference

Please Note:

  • This Alora LED fixture comes with pre-wired LED module(s)
  • Unless instructed, Do Not touch any part of the LED module(s) as any unnecessary contact with the module could cause permanent damage
  • For dimming, an ELV (Electronic Low Voltage) or TRIAC type of dimmer is required
  • 120V input

NOTICE

  • The important safeguards and instructions outlined in this sheet cannot cover all possible conditions and situations that may occur. It must be understood that caution and certain care factors must be followed. These instructions are provided for your safety and we highly recommend that a licensed, trained electrician install this unit.

ASSEMBLY INSTRUCTIONS

  • Step 1
    Remove fixture from its original package.

  • Step 2
    Separate mounting plate (1c) from canopy (2a) by removing canopy screws (2b).

  • Step 3
    Attach mounting plate (1c) to electrical junction box (1a) using junction box screws provided (1e) in hardware package.

  • Step 4
    Secure mounting plate (1c) to mounting surface with anchors (1f) and screws (1g)

  • Step 5
    Determine hanging height of fixture by securing rods (2d) to canopy (2a) and fixture body (3a) after feeding fixture wires (LED+ and LED-) through rods

  • Step 6
    Make proper electrical connections between LED and DC driver, LED- Negative, LED+ Positive using wire nuts provided (See Illustration 1 and refer to diagram on driver)

  • Step 7
    Make proper electrical connections (black to hot “L”, white to neutral “N”, ground to “GND”) with wire nuts (1b) provided in hardware package and place driver (4a) inside canopy (2a).

  • Step 8
    Secure glass (3b) to fixture body (3a) by threading clockwise.

  • Step 9
    Attach canopy (2a) to mounting plate (1c) with canopy screws (2b).
    You are now ready to enjoy your fixture.

P: 1.855.855.8926
CANADA : 19054 28th Avenue Surrey – BC V3Z 6M3
USA : 3035 E. Lone Mountain Rd – Las Vegas, NV, 89081 www.aloralighting.com
20230619

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals