LP338052UBAR Alora Ten Light Linear Pendant User Manual
- June 13, 2024
- aLora
Table of Contents
LP338052UBAR Alora Ten Light Linear Pendant
Product Information
- Model Number : LP338052
- Product Name : Linear Pendant
- Manufacturer : Alora Lighting
- Technical Support : 1.855.855.8926
- Email: technicalsupport@aloralighting.com
- Website: www.aloralighting.com
Product Usage Instructions
- Remove the fixture from its original package.
- Separate the mounting plate (1c) from the canopy (2a) by loosening the two canopy pivots (2b).
- Important: This fixture must be mounted independently from the junction box. Additional means of support are required.
- Secure the mounting plate (1c) to the mounting surface using anchors (1f) and screws (1g).
- Secure the canopy pivots (2b) to the canopy (2a) and secure them with the mounting collar nut (2c).
- Determine the hanging height of the fixture by securing rods (2d) to the canopy pivots (2b) and the fixture body after feeding the fixture wires through the rods.
- Make proper electrical connections by using wire nuts (1b) provided in the hardware package. Connect black to hot L, white to neutral N, and ground to GND.
- Attach the fixture shade (3b) to the fixture (3a) and secure it with the socket nut (3c) using the socket nut wrench (4b).
- Install the recommended lamp (4a) (not provided) to the fixture socket, referring to the socket label for maximum wattage and type.
- Secure the canopy (2a) to the mounting plate (1c) by attaching the canopy pivot (2b) to the hickey (5a).
You are now ready to enjoy your fixture.
WARNINGS AND CAUTIONS
- Make sure POWER is COMPLETELY OFF at the fuse box
- Have your fixture installed by a qualified licensed electrician
- Prepare everything in a clear area
- Wear gloves at all times during this installation
- Read instructions carefully before you start assembly
- Keep this installation sheet for future reference
Please Note
- 120V input
NOTICE
The important safeguards and instructions outlined in this sheet cannot cover
all possible conditions and situations that may occur. It must be understood
that caution and certain care factors must be followed. These instructions are
provided for your safety and we highly recommend that a licensed, trained
electrician install this unit.
ASSEMBLY INSTRUCTIONS
- Step 1
- Remove fixture from its original package.
- Step 2
- Separate mounting plate (1c) from canopy (2a) by loosening the two canopy pivots (2b).
- Important: This fixture must be mounted independently from junction box, additional means of support is required.
- Step 3
- Secure mounting plate (1c) to mounting surface with anchors (1f) and screws (1g)
- Step 4
- Secure canopy pivots (2b) to canopy (2a) and secure with mounting collar nut (2c).
- Step 5
- Determine hanging height of fixture by securing rods (2d) to canopy pivots (2b) and fixture body after feeding fixture wires through rods.
- Step 6
- Make proper electrical connections (black to hot “L”, white to neutral “N”, ground to “GND”) with wire nuts (1b) provided in hardware package.
- Step 7
- Attach fixture shade (3b) to fixture (3a) and secure with socket nut (3c) using socket nut wrench (4b). Install the recommended lamp (4a) (not provided) (referred on the socket label for maximum wattage and type) to fixture socket.
- Step 8
- Secure canopy (2a) to mounting plate (1c) by attaching canopy pivot (2b) to hickey (5a).
- You are now ready to enjoy your fixture.
P: 1.855.855.8926
CANADA : 19054 28th Avenue Surrey – BC V3Z 6M3
USA : 3035 E. Lone Mountain Rd – Las Vegas, NV, 89081
www.aloralighting.com
20230619
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>