FORTIN 111591 2023 Push Start Remote Starters and Alarm Systems Installation Guide

FORTIN 111591 2023 Push Start Remote Starters and Alarm Systems

Vehicle Functions

COMPATIBLE MODULE REQUIRED

Program bypass option

Parts required (Not included)

• 2X 1 AMP Diode

NOTES

• MAKE SURE THE KEY IS NOT INSIDE THE CAR WHEN REMOTE STARTING.

MANDATORY INSTALL

HOOD PIN

HOOD STATUS: THE HOOD PIN SWITCH MUST BE INSTALLED IF THE VEHICLE CAN BE REMOTE STARTED WITH THE HOOD OPEN, SET FUNCTION A11 TO OFF.

• A11
  • OFF

Notice: the installation of safety elements are mandatory. The hood pin is an essential security element and must be installed.

THIS MODULE MUST BE INSTALLED BY A QUALIFIED TECHNICIAN. A WRONG CONNECTION CAN CAUSE PERMANENT DAMAGE TO THE VEHICLE.

DESCRIPTION

AUTOMATIC TRANSMISSION WIRING CONNECTION

KEY BYPASS PROGRAMMING PROCEDURE

OEM remote

• Keep the other OEM remotes away from the vehicle. Minimum 3 meters (10 feet).

1. Press and hold Insert the programming button: the 4-Pin (Data-Link) connector.
   • The Blue, Red, Yellow and Blue & Red LEDs will alternatively illuminate.
2. Release the programming button when the LED is BLUE.
   • If the LED is not solid BLUE disconnect the 4-Pin connector (Data-Link) and go back to step 1.
3. Insert the required remaining connectors.
4. Do not press the brake pedal. Press the START/STOP button twice to turn ON the ignition.
5. Press and release the programming button once (1x).
   • The BLUE LED will turn off.
   • The BLUE LED will flash rapidly.
6. Press the START/STOP button once to turn OFF the ignition.
   • The BLUE LED will turn ON solid.
7. Remove the battery from 1 OEM remote.
   • OEM remote
   • Keep the other OEM remotes away from the vehicle. Minimum 3 meters (10 feet).
8. Place the OEM remote (no battery) close to the front of START/STOP button as shown.
9. Press the footbrake pedal.
   • The vehicle ignition will turn ON.
   • The RED RED will turn ON.
   • The RED BLUE will turn OFF.
   • Release the pedal.
10. Press the START/STOP button once to turn OFF the ignition.
11. Place the OEM remote (no battery) close to the front of START/STOP button as shown.
12. Press the footbrake pedal.
    • The vehicle ignition will turn ON.
    • The YELLOW LED will turn ON.
    • The RED LED will turn OFF.
    • Release the pedal.
13. Press the START/STOP button once to turn OFF the ignition.
    • The RED and YELLOW LEDs will alternated.
14. Disconnect all the connectors and after the Data-Link (4-pins) connector.
15. Use the tool: FLASH LINK UPDATER or FLASH LINK MOBILE to visit the DCryptor menu.
    • Parts required (not included)
16. AFTER DCRYPTOR PROGRAMMING COMPLETED
    • Go back to the vehicle and reconnect the 4-Pin (Data-Link) connector and after, all the remaining connector.
    • The module is now programmed.
    • REMOTE STARTER / ALARM VERIFICATION: Test the remote starter. Remote start the vehicle.

FUNCTIONS

• All key must be outside the vehicle.
• All doors must be closed.
• Remote start the vehicle.
• Unlock the doors with the remote-starter remote.
• Enter the vehicle with the SMART-KEY.
• Press the brake pedal.
• The vehicle can now be put in to gear and driven.

Warning

• The engine will shutdown when a door is open if the vehicle is not Unlock.

Notice: Updated Firmware and Installation Guides

Updated firmware and installation guides are posted on our website on a regular basis. We recommend that you update this module to the latest firmware and download the latest installation guide(s) prior to the installation of this product.

Module label

WARNING

The information on this sheet is provided on an (as is) basis with no representation or warranty of accuracy whatsoever. It is the sole responsibility of the installer to check and verify any circuit before connecting to it. Only a computer-safe logic probe or digital multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or responsibility whatsoever pertaining to the accuracy or currency of the information supplied. The installation in every case is the sole responsibility of the installer performing the work and FORTIN ELECTRONIC SYSTEMS assumes no liability or responsibility whatsoever resulting from any type of installation, whether performed properly, improperly or any other way. Neither the manufacturer or distributor of this module is responsible of damages of any kind indirectly or directly caused by this module, except for the replacement of this module in case of manufacturing defects. This module must be installed by qualified technician. The information supplied is a guide only. This instruction guide may change without notice. Visit www.fortinbypass.com to get the latest version.

Contact

TECH SUPPORT

• Tél: 514-255-HELP (4357)
  • 1-877-336-7797
• WEB UPDATE:www.fortinbypass.com

This guide may change without notice. See www.fortin.ca for latest version.

Copyright © 2006-2019, FORTIN AUTO RADIO INC ALL RIGHTS RESERVED PATENT PENDING

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>