FORTIN 102961 2017 Volkswagen Golf R Push Button Remote Starters and Alarm Systems Installation Guide
- June 13, 2024
- FORTIN
Table of Contents
REV.: 20211020 GUIDE # 102961
THAR-VW1 INSTALLATION
ADDENDUM – SUGGESTED WIRING CONFIGURATION
|
Vehicle functions supported in this diagram (functional if equipped)
---|---
|
Immobilizer bypass with TB-VW (Sold separately)| T-Harness available (sold
separately)| Lock| Unlock| Arm| Disarm| Parking Lights| Tachometer|
AUX.1 Comfort Group
| Door Status| Trunk Status| Hood Status*| Hand-Brake Status| Foot-Brake
Status| OEM Remote monitoring| R.S. OEM remote Stand Alone compatible
VEHICLE| YEARS| Heated seats| Rear defrost
VOLKSWAGEN
Golf-R
Push-to-Start
| 2015-2018|
•
| •| •| •| •| •| •| •| •| •| •| •| •| •| •|
•
| •
|
COMPATIBLE MODULE REQUIRED:
|
QR CODE ON THE LABEL
|
FIRMWARE VERSION
64.[06]
VW MINIMUM
|
To add the firmware version and the options, use the FLASH LINK UPDATER or FLASH LINK MOBILE tool, sold separately.
---|---|---|---|---
MANUFACTURED AFTER: 2019
| Parts required (Not included)
---|---
| 1x TB-VW (key bypass)
| PROGRAMMING TOOL REQUIRED for key bypass programming.
Sold separately
---|---
WARNING
| Vehicle’s equipped with Virtual Cluster, not supported for the key bypass.
MANDATORY INSTALL
* HOOD PIN
CONTACT
HOOD STATUS : THE HOOD PIN SWITCH (INCLUDED) MUST BE INSTALLED IF THE VEHICLE CAN BE REMOTE STARTED WITH THE HOOD OPEN, SET FUNCTION A11 TO OFF.
| A11| | SECURITY STICKER
Included
Inclus
Notice: the installation of safety elements are mandatory. The hood pin and the sticker are essential security elements and must be installed.
THIS MODULE MUST BE INSTALLED BY A QUALIFIED TECHNICIAN. A WRONG CONNECTION CAN CAUSE PERMANENT DAMAGE TO THE VEHICLE.
This guide may change without notice. See www.fortin.ca for latest version.
NOTES
|
Program bypass option:
|
UNIT OPTION
| DESCRIPTION
---|---|---|---
C1
| OEM Remote status (Lock/Unlock) monitoring
|
D6
| Push-to-Start
Program bypass option
(If equipped with OEM alarm):|
D2
| Unlock before / Lock after (Disarm OEM alarm)
IF THE VEHICLE IS NOT EQUIPPED WITH FUNCTIONAL HOOD PIN:
|
A11
| | Hood trigger (Output Status).
|
Program remote starter option for Diesel vehicules:
|
UNIT OPTION
|
MODE
| DESCRIPTION
---|---|---|---|---
18
|
5
| Enable (5 seconds) delay between Ignition power up and Starter (crank)
|
32
|
6
| Bypass control
for R.S. OEM REMOTE STAND ALONE:
|
38
|
5
| Enable (Press Lock, Unlock and Lock to remote start)
for COMFORT GROUP ACTIVATION:
|
39
|
2
| Temperature option : AUX.1 activated at 5°C, 5 seconds after remote started
DESCRIPTION
(1) Under the steering column
(2) Under steering column cover.
(3) VESCM – Electrical System Control Module under dash driver side, above
Driver Kick Panel
(4) OBD-II connector
(5) Parking lights switch
(6) Under the hood, at starter relay.
Pull the clips to release the cover of the connector.
- Clips
AUTOMATIC TRANSMISSION WIRING CONNECTION
MANUAL TRANSMISSION WIRING CONNECTION
DCRYPTOR PROGRAMMING PROCEDURE
Parts required (not included)
1x 
,
1x 
1x Microsoft Windows Computer with Internet connection
OR
1x 
1x 
1x Smartphone Android or iOS with Internet connection
(Internet provider charges may apply)
BEFORE PROGRAMMING SET THE UNIT OPTIONS AND SAVE.
[1]
Take out the battery from the remote control.
[2]
Place the transponder’s ring in front of the remote control.
[3]
With the remote beside the antenna ring, proceed with the programming on the next pages.
[4]
*USE THE R-LINK TOOL FOR PROGRAMMING*
Sold separately
Connect the R-LINK instead of the TB-VW.
- (~) RX White or Lt.Blue/Black
- (~) TX Blue or Lt.Blue
- Ground Black
- (+)12V Red
- White/Red or Green
- White/Green or Green/Black
[5]
WARNING:
Close and open the driver door.
KEY BYPASS PROGRAMMING PROCEDURE
[6]
Press and hold the programming button:
Connect the 4-Pin Data-link connector.
[7]
Release the programming button when the BLUE LED is ON.
If the LED is not solid BLUE disconnect the 4-PIN Data-link harness (Black connector).
[8]
Insert the required remaining connectors.
[9]
Press the Push-to-Start button to turn ON the ignition.
[10]
Press and release the programming button once (1x).
The BLUE LED will turn off.
Wait,
The BLUE LED will flash rapidly.
[11]
Press and hold the programming button.
The BLUE LED will turn OFF.
Wait,
The RED LED will turn ON.
Release the programming button.
[12]
WAIT,
this process may take up to 5 minutes
Wait , do not touch the vehicle or the module.
The BLUE, RED and YELLOW LEDs will rapidly alternate.
the RED LED to turn ON.
Wait,
the YELLOW LED will flash once.
[13]
Wait,
Wait for the RED and YELLOW LEDs to slowly alternate.
If the RED LED flashes slowly, the programming has failed, go back to step1 and start the programming over.
[14]
Press the Push-to-Start button once to turn off the ignition.
[15]
Disconnect all connectors and after the 6-Pin (Main-Harness) or the 4-Pin Data-link connector.
[16]
Microsoft Windows Computer
with Internet connection*
[OR]
- VEHICLE’S OBDII CONNECTOR
- Smartphone*
(Internet provider charges may apply)
Use the tool:
FLASH LINK UPDATER or FLASH LINK MOBILE to visit the DCryptor menu.
*Parts required (not included)
[17]
AFTER DCRYPTOR PROGRAMMING COMPLETED
Go back to the vehicle and reconnect the 6-Pin (Main-Harness) or the
4-pins (Data-Link) connector and after all the remaining connector.
NOTE
IF PROGRAMMING IS INTERRUPTED DURING THE PROCESS, SUCH AS A MODULE IS
DISCONNECTED OR BY TURNING OFF THE IGNITION WITH THE KEY, IT IS POSSIBLE THAT
THE VEHICLE WILL NO LONGER START NORMALLY, YOU MUST DISCONNECT AND RECONNECT
THE VEHICLE BATTERY TO CORRECT THE SITUATION.
[18]
Take out the remote control from the transponder’s ring.
[19]
Insert the battery into the remote control.
[20]
Connect the TB-VW instead of the R-LINK.
- (~) RX White or Lt.Blue/Black
- (~) TX Blue or Lt.Blue
- Ground Black
- (+)12V Red
- White/Red or Green
- White/Green or Green/Black
The module is now programmed.
REMOTE STARTER / ALARM VERIFICATION PROCEDURE
Test the remote starter. Remote start the vehicle.
REMOTE STARTER PROGRAMMING PROCEDURE
REFER TO THE QUICK INSTALL GUIDE INCLUDED WITH THE MODULE FOR THE REMOTE STARTER PROGRAMMING.
REMOTE STARTER FUNCTIONALITY
All doors must be closed.
Remote start the vehicle.
Unlock the doors with either:
• The OEM remote
• The remote-starter remote.
Enter the vehicle with the Intelligent SmartKey.
The vehicle can now be put in to gear and driven.
Module label
Notice: Updated Firmware and Installation Guides
Updated firmware and installation guides are posted on our web site on a
regular basis. We recommend that you update this module to the latest firmware
and download the latest installation guide(s) prior to the installation of
this product.
WARNING
The information on this sheet is provided on an (as is) basis with no
representation or warranty of accuracy whatsoever. It is the sole
responsibility of the installer to check and verify any circuit before
connecting to it. Only a computer safe logic probe or digital multimeter
should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or
responsibility whatsoever pertaining to the accuracy or currency of the
information supplied. The installation in every case is the sole
responsibility of the installer performing the work and FORTIN ELECTRONIC
SYSTEMS assumes no liability or responsibility whatsoever resulting from any
type of installation, whether performed properly, improperly or any other way.
Neither the manufacturer or distributor of this module is responsible of
damages of any kind indirectly or directly caused by this module, except for
the replacement of this module in case of manufacturing defects. This module
must be installed by qualified technician. The information supplied is a guide
only. This instruction guide may change without notice. Visit
www.fortinbypass.com to get the latest version.
Copyright © 2006-2019, FORTIN AUTO RADIO INC ALL RIGHTS RESERVED PATENT PENDING
TECH SUPPORT
Tél: 514-255-HELP (4357)
1-877-336-7797
ADDENDUM GUIDE
WEB UPDATE
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>