FORTIN Chevrolet Avalanche 2013 Standard-Key Remote Starters and Alarm Systems Installation Guide
- June 13, 2024
- FORTIN
Table of Contents
REV.: 20211022 Guide #
102851
REGULAR INSTALLATION
ADDENDUM – SUGGESTED WIRING CONFIGURATION
|
Vehicle functions supported in this diagram (functional if equipped)
---|---
|
Immobilizer Bypass| T-Harness| Lock| Unlock| Arm| Disarm| Trunk (open)|
Tachometer| Heated Seats| Door Status| Trunk Status| Hood Status| Hand-Brake
Status| Foot-Brake Status| PK3, Passlock| OEM Remote monitoring|
R.S. OEM remote Stand Alone compatible
VEHICLE| YEARS
CHEVROLET| | |
Avalanche| 2007-2013|
•
| •| •| •| •| •| •| •| •| •| •| •| •| •| •| •|
•
|
BYPASS FIRMWARE VERSION
70.[41]
GM MINIMUM
|
To add the firmware version and the options, use the FLASH LINK UPDATER or FLASH LINK MOBILE tool, sold separately.
---|---|---
|
Program bypass option:
|
UNIT OPTION
| DESCRIPTION
---|---|---|---
C1
| OEM Remote status (Lock/Unlock) monitoring
IF THE VEHICLE IS NOT EQUIPPED WITH FUNCTIONAL HOOD PIN:
|
A11
| | Hood trigger (Output Status).
---|---|---|---
|
Program remote starter option for R.S. OEM REMOTE STAND ALONE:
|
FUNCTION
|
MODE
| DESCRIPTION
---|---|---|---|---
38
|
2
| Enable
Press 3x Lock to remote start with the OEM remote.
MANDATORY INSTALL
* HOOD PIN
CONTACT
HOOD STATUS : THE HOOD PIN SWITCH (INCLUDED) MUST BE INSTALLED IF THE VEHICLE CAN BE REMOTE STARTED WITH THE HOOD OPEN, SET FUNCTION A11 TO OFF.
| A11|
Notice: the installation of safety elements are mandatory. The hood pin and the sticker are essential security elements and must be installed.
THIS MODULE MUST BE INSTALLED BY A QUALIFIED TECHNICIAN. A WRONG CONNECTION CAN CAUSE PERMANENT DAMAGE TO THE VEHICLE.
This guide may change without notice. See www.fortin.ca for latest version.
DESCRIPTION
a) Ignition connector*
b) Ignition Barrel
c) Transponder connector
d) BCM Driver’s side dash
WIRING CONNECTION
-
HOOD PIN (If the vehicle is not equipped with a hood pin)
-
CUT LOOP FOR AUTOMATIC TRANSMISSION MODE.
-
*Use a more powerful 12V source if your system required more than 2 Amp.
-
Ignition Barrel
-
*The connector may differ from the one shown
-
Ignition connector*
Back View
White connector -
Transponder connector
Back View
White connector -
25-Pin Back View Brown connector.
KEY BYPASS PROGRAMMING PROCEDURE
[1]
- LED may differ depending on the module casing.
Press and hold the programming button: Connect the 6-PIN Main harness (White connector).
The Blue, Red, Yellow and Blue & Red LEDs will alternatively illuminate.
[2]
Release the programming button when the LED is BLUE.
If the LED is not solid BLUE disconnect the 6-Pin connector (Main-Harness) and go back to step 1.
[3]
Insert the required remaining connectors.
[4]
Turn the key to the Ignition ON/RUN position.
The BLUE LED will flash rapidly.
[5]
Press and release the programming button once (1x).
The Blue LED will turn OFF.
The YELLOW and RED LEDS will alternate…
[6]
Turn the key to the OFF position.
[7]
Disconnect all connectors and after the 6-Pin (Main-Harness) or the 4-Pin Data-link connector.
[8]
Microsoft Windows
Computer with Internet connection*
[OR]
- VEHICLE’S OBDII CONNECTOR
- **Smartphone***
(Internet provider charges may apply)
Use the tool:
FLASH LINK UPDATER or FLASH LINK MOBILE to visit the DCryptor menu.
*Parts required (not included)
[9]
AFTER DCRYPTOR PROGRAMMING COMPLETED
Go back to the vehicle and reconnect the 6-Pin (Main-Harness) or the
4-pins (Data-Link) connector and after all the remaining connector.
The module is now programmed.
REMOTE STARTER / ALARM VERIFICATION PROCEDURE
Test the remote starter. Remote start the vehicle.
REMOTE STARTER PROGRAMMING PROCEDURE
REFER TO THE QUICK INSTALL GUIDE INCLUDED WITH THE MODULE FOR THE REMOTE STARTER PROGRAMMING.
REMOTE STARTER FUNCTIONALITY
All doors must be closed.
Remote start the vehicle.
Unlock the doors with the remote-starter remote or the OEM remote.
Insert and Turn the key to the Ignition ON/RUN position.
Press the brake pedal.
The vehicle can now be put in to gear and driven.
Module label
Notice: Updated Firmware and Installation Guides
Updated firmware and installation guides are posted on our web site on a
regular basis. We recommend that you update this module to the latest firmware
and download the latest installation guide(s) prior to the installation of
this product.
WARNING
The information on this sheet is provided on an (as is) basis with no
representation or warranty of accuracy whatsoever. It is the sole
responsibility of the installer to check and verify any circuit before
connecting to it. Only a computer safe logic probe or digital multimeter
should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or
responsibility whatsoever pertaining to the accuracy or currency of the
information supplied. The installation in every case is the sole
responsibility of the installer performing the work and FORTIN ELECTRONIC
SYSTEMS assumes no liability or responsibility whatsoever resulting from any
type of installation, whether performed properly, improperly or any other way.
Neither the manufacturer or distributor of this module is responsible of
damages of any kind indirectly or directly caused by this module, except for
the replacement of this module in case of manufacturing defects. This module
must be installed by qualified technician. The information supplied is a guide
only. This instruction guide may change without notice. Visit
www.fortinbypass.com to get the latest version.
Copyright © 2006-2018, FORTIN AUTO RADIO INC ALL RIGHTS RESERVED PATENT PENDING
TECH SUPPORT
Tél: 514-255-HELP (4357)
1-877-336-7797
ADDENDUM GUIDE
WEB UPDATE
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>