Ustellar UTS33381-RGB LED RGB Light Strip User Guide
- June 3, 2024
- Ustellar
Table of Contents
Ustellar UTS33381-RGB LED RGB Light Strip
THANK YOU for choosing Ustellar. To optimize user experience, please use the product according to the following instructions.
Warning
- READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
- This light strip is designed to match the power adapter output, so the strip length CAN NOT be extended according to the power limitation.
- Do not cover this product as the covering may cause the flexible light to overheat and melt or ignite.
- Do not operate with the flexible light tightly coiled.
- Do not route the cord or flexible lighting through walls, doors, windows or any like part of the building structure.
- Do not use if there is any damage to the light or cord insulation. Inspect periodically.
- Do not submerge flexible light in liquids, or use the product in the vicinity of standing water or other liquids.
- Secure this flexible light using only the hangers or clips provided. Do not secure this product or its cord with staples, nails, or like means that may damage the insulation or permanently attach to the building structure.
- Do not subject flexible lighting to continuous flexing.
Specification
Components
LED Signal Receiver
RF Remote Controller
Three Settings
There are three flexible settings for the remote controller(fs) to control the light strip(s) as per your lighting project, One-to-One Setting, One-to-Many Setting, and Many-to-Many Setting. You can choose either which light strip and how many light strips one controller controls, or which controller and how many controllers control the light strip(s).
- One-to-One Setting: One remote controller can only control one light strip. Turn on the remote controller and power on the LED Signal Receiver of the light strip. During the first 5 seconds, immediately long press the bottom left button on the remote controller till the strip light blinks. Then the ‘One-to-One Setting’ is done. One-to-One Setting is the factory default.
- One-to-Many Setting: If you want to control many light strips with one remote controlle, you could choose the ‘One-to-Many’Setting. Tun on the remote controller and power on all LED Signal Receivers of the light strips. During the first 5 seconds, immediately long press the bottom left button on the remote controller till the strip lights blink. Then the ‘One-to-Many Setting’ is done.
- Many-to-Many Setting: f you have many light strips and remote controllers, and hope that any of the controllers can control all the light strips, you could choose the ‘Many-to-Many’ Setting. Turn on each remote controller and power on its LED Signal Receiver. During the first 5 seconds, immediately long press the bottom right button on the remote controller till the strip light blinks.
Installation
How to connect all parts?
- Connect the light strip to the controller cable, and then connect the controller cable to the power adapter
- Plug the adapter into the socket and turn on the light strip by pressing the ON button on the RF remote controller.
How to cut the LED strip if necessary?
Before cutting the LED Strip, please keep these in mind.
- Once the strip is cut, the rest part being cut can not work. So it’s not recommended to cut the strip unless it is really necessary.
- After the strip is cut, please use the sealing glue (attached) to seal the end of the strip. Otherwise, the light strip can not retain waterproof and may be damaged while usage.
- Cut the strip along the marks.
How to control the light strip
- Download the App Lotus Lantern by scanning the QR code below. This App is compatible with Android 4,0 and ios 8.1 or above.
- Power on the light.
- Activate the Bluetooth function on your phone and open the App to automatically connect to the light.
- Enjoy the lighting by exploring the functions such as brightness, modes, music sync, timer etc Via the App.
We hereby declare that the objects of the above declaration comply with the provisions of the following EU directives and harmonized standards:
This product is subject to the provisions of European Directive 2012/19/EC. The symbol showing a wheelie bin crossed through indicates that the product requires separate refuse collection in the European Union.This applies to the product and all accessories marked with this symbol. Products identified with this symbol may not be discarded with normal household waste, but must be taken to a collection point for recycling electric and electronic appliances. This recycling symbol marks e.g an object or parts of the material as valuable for recycling. Recycling helps to reduce the consumption of raw materials and protect the environment.
Contact Us
Have some issues? No worries! Please reach us via these channels.
Our customer services team is more than happy to help.
www.ustellar.com
support@ustellar.com
Manufacturer: Shenzhen Ustellar Technology Ltd.(Shenzhen shi you shi to keep you xian gong si)
Address: Rm.C306, 3/F, C Bldg., Youth Entrepreneur Hub, Jianshe East Rd., SZ, CN
Name: Bright star consulting e.K.
Adresse: Humboldtstr.5, 31812 Bad Pyrmont Germany
E-Mail: utaundnico@hotmail.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>