FORTIN 102371 Suzuki Equator 2009 Standard Key Remote Starters And Alarm Systems Installation Guide

REV.: 20211104
Guide # 102371
THAR-ONE-NIS2 THARNESS INSTALLATION
ADDENDUM – SUGGESTED WIRING CONFIGURATION

102371 Suzuki Equator 2009 Standard Key Remote Starters And Alarm Systems

Vehicle functions supported in this diagram (functional if equipped)

VEHICLE| YEARS| bypass| T-Harness| Lock| Unlock| Arm| Disarm| Tachometer| Parking Light| Auto light| Door Status| Trunk Status| Hood Status*| Hand-Brake Status| Foot-Brake Status
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---
Equator| 2009-2011| ●| ●| ●| ●| ●| ●| ●| ●| ●| ●| ●| ●| ●| ●

BYPASS FIRMWARE VERSION
72.[48] NISSAN/MINIMUM
To add the firmware version and the options, use the FLASH LINK UPDATER or FLASH LINK MOBILE tool, sold separately.

Program bypass option IF THE VEHICLE IS NOT EQUIPPED WITH FUNCTIONAL HOOD PIN:

Program remote starter option

MANDATORY INSTALL

*HOOD PIN

HOOD STATUS: THE HOOD PIN SWITCH (INCLUDED) MUST BE INSTALLED IF THE VEHICLE CAN BE REMOTE STARTED WITH THE HOOD OPEN, SET FUNCTION All TO OFF.

A11

Notice: the installation of safety elements are mandatory. The hood pin and the sticker are essential security elements and must be installed.
THIS MODULE MUST BE INSTALLED BY A QUALIFIED TECHNICIAN. A WRONG CONNECTION CAN CAUSE PERMANENT DAMAGE TO THE VEHICLE.

WIRING CONNECTION

KEY BYPASS PROGRAMMING PROCEDURE 1/2

Press and hold the programming button: Connect the 6-PIN Main harness (White connector).
The Blue, Red, Yellow and Blue & Red LEDs will alternatively illuminate.

Release the programming button when the LED is YELLOW.
If the LED is not solid YELLOW disconnect the 6-pin connector (Main-Harness) and go back to step 1.

Insert the required remaining connectors.

Press and release the programming button two times (2x).
The YELLOW LED will alternate between 2x flashes and a pause.
‘Wait until the YELLOW LED turns ON.

Turn the key to the Ignition ON/RUN position.
The RED LED will turns ON.

If the YELLOW and RED LEDs are not solid remove the key and go back to step 5.
Repeat this step until the RED and YELLOW LED are solid.

Wait for the BLUE LED to flash rapidly.

Turn the key to the OFF position.

Remove the key from the ignition barrel.

Turn the key to the Ignition ON/RUN position.
The BLUE, YELLOW and RED LED’s will rapidly alternate.
When the YELLOW LED begins to flash rapidly: Key bypass programmed.

Turn the key to the OFF position.

The module is now programmed.
Use the remote of the remote starter or security system to test all of the supported features to ensure proper programming.

REMOTE STARTER PROGRAMMING PROCEDURE

REFER TO THE QUICK INSTALL GUIDE INCLUDED WITH THE MODULE FOR THE REMOTE STARTER PROGRAMMING.

REMOTE STARTER FUNCTIONALITY

All doors must be closed.| Remote start the vehicle.| Unlock the doors with the remote-starter remote or the OEM remote.

Insert and Turn the key to the Ignition ON/RUN position.| Press the brake pedal.| The vehicle can now be put in to gear and driven.

www.fortinbypass.com

Module label
Notice: Updated Firmware and Installation Guides
Updated firmware and installation guides are posted on our web site on a regular basis. We recommend that you update this module to the latest firmware and download the latest installation guide(s) prior to the installation of this product.

WARNING
The information on this sheet is provided on an (as is) basis with no representation or warranty of accuracy whatsoever.
It is the sole responsibility of the installer to check and verify any circuit before connecting to it. Only a computer safe logic probe or digital multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or responsibility whatsoever pertaining to the accuracy or currency of the information supplied. The installation in every case is the sole responsibility of the installer performing the work and FORTIN ELECTRONIC SYSTEMS assumes no  liability or responsibility whatsoever resulting from any type of installation, whether performed properly, improperly or any other way. Neither the manufacturer or distributor of this module is responsible of damages of any kind  indirectly or directly caused by this module, except for the replacement of this module in case of manufacturing defects. This module must be installed by qualified technician. The information supplied is a guide only. This instruction  guide may change without notice. Visit www.fortinbypass.com to get the latest version.

TECH SUPPORT
Tél: 514-255-HELP (4357)
1-877-336-7797
ADDENDUM GUIDE

www.fortinbypass.com
WEB UPDATE

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>