FORTIN 92011 2017 Volkswagen Tiguan Remote Starters Regular Key And Alarm Systems Installation Guide

INSTALLATION WITH TB-VW
REV.: 20211028
Guide # 92011 VEHICLE
YEARS

ADDENDUM – SUGGESTED WIRING CONFIGURATION
Vehicle functions supported in this diagram (functional if equipped)

VOLKSWAGEN

| BYPASS
FIRMWARE VERSION| To add the firmware version and the options, use the FLASH LINK UPDATER or FLASH LINK MOBILE tool, sold separately.
---|---|---

Program bypass option:
Program bypass option (If equiped with OEM alarm):
IF THE VEHICLE IS NOT EQUIPPED WITH FUNCTIONAL HOOD PIN:

Program remote starter option only if brake must be pressed to start :

Program remote starter option for R.S. OEM REMOTE STAND ALONE:

Press 3x Lock to remote start with the OEM remote.

MANDATORY INSTALL

• HOOD PIN CONTACT HOOD STATUS : THE HOOD PIN SWITCH (INCLUDED)
  MUST BE INSTALLED IF THE VEHICLE CAN BE REMOTE STARTED WITH THE HOOD OPEN, SET FUNCTION A11 TO OFF.

A11|
---|---

ATTENTION  SECURITY STICKER
WARNING
Included
Notice: the installation of safety elements are mandatory. The hood pin and the sticker are essential security elements and must be installed.
THIS MODULE MUST BE INSTALLED BY A QUALIFIED TECHNICIAN. A WRONG CONNECTION CAN CAUSE PERMANENT DAMAGE TO THE VEHICLE.
This guide may change without notice. See www.fortin.ca for latest version.

PARTS REQUIRED

| Parts required (Not included)| PAGE
---|---|---
WIRE TO WIRE DIAGRAM
AUTOMATIC TRANSMISSION| 1x TB-VW (key bypass)
1x Fusible 7.5 Amp.
1x Relay (Parking lights)| page 4
MANUAL TRANSMISSION| 1x TB-VW (key bypass)
1x RLINK programming tool
1x Fusible 7.5 Amp.
1x Relay (Parking lights)| page 5

THARNESS DIAGRAM

| | Parts required (Not included)| PAGE
---|---|---|---
THARNESS DIAGRAM
THARNESS THAR-VW6| AUTOMATIC TRANSMISSION| 1x TB-VW (key bypass)
1x THAR-VW6| page 6
MANUAL TRANSMISSION| 1x TB-VW (key bypass)
1x THAR-VW6| page 7
THARNESS THAR-VW2| AUTOMATIC TRANSMISSION| 1x TB-VW (key bypass)
1x THAR-VW2| page 8
MANUAL TRANSMISSION| 1x TB-VW (key bypass)
1x THAR-VW2| page 9
| Parts required (Not included)
---|---
| 1x TB-VW (key bypass)

PHOTOS & LOCATIONS

TB-VW AUTOMATIC TRANSMISSION WIRING CONNECTION TB-VW MANUAL TRANSMISSION WIRING CONNECTION TB-VW – THAR-VW6 – AUTOMATIC TRANSMISSION WIRING CONNECTION TB-VW – THAR-VW6 – MANUAL TRANSMISSION WIRING CONNECTION TB-VW – THAR-VW2 – AUTOMATIC TRANSMISSION WIRING CONNECTION TB-VW – THAR-VW2 – MANUAL TRANSMISSION WIRING CONNECTION

DCRYPTOR PROGRAMMING PROCEDURE

Parts required (not included)

| FLASH LINK UPDATER,
---|---
| FLASH LINK MANAGER SOFTWARE | PROGRAMME
| Microsoft Windows Computer with Internet connection

OR

| FLASH LINK MOBILE
---|---
| FLASH LINK MOBILE APP
| Smartphone Android or iOS with Internet connection (Internet provider charges may apply)

BEFORE PROGRAMMING SET THE UNIT OPTIONS AND SAVE.

| WARNING:
Close and open the driver door.
---|---
| The Blue, Red, Yellow and Blue & Red LEDs will alternatively illuminate. Press and hold the
programming button: Connect the 6-PIN Main harness (White connector).
| Release the programming button when the Blue LED is ON.

If the LED is not solid BLUE disconnect the 6-Pin connector (Main-Harness) and go back to step1.
| Connect the required remaining harnesses.
| Wait,
The BLUE LED will flash rapidly.
Turn the key to the Ignition ON/RUN position.
| Press and hold the programming button.
The BLUE LED will turn OFF.
Wait,
The RED LED will turn ON.
Release the programming button.

KEY BYPASS PROGRAMMING PROCEDURE 2/4

7 | Wait, do not touch the vehicle or the module.
The BLUE, RED and YELLOW LEDs will rapidly alternate. Wait,  the RED LED to turn ON.
---|---
8.| Wait,
Wait for the RED and YELLOW LEDs to slowly alternate.
If the RED LED flashes slowly, the programming has failed, go back to step1 and start the programming over.
9. | Turn the key to the OFF position.
10. | Disconnect all connectors and after the 6-Pin (Main-Harness) or the 4-Pin Data-link connector.
11. | Use the tool:
FLASH LINK UPDATER or FLASH LINK MOBILE to visit the DCryptor menu.
*Parts required (not included)
12. | AFTER DCRYPTOR PROGRAMMING COMPLETED
Go back to the vehicle and reconnect the 6-Pin (MainHarness) or the 4-pins (Data-Link) connector and after all the remaining connector.

KEY BYPASS PROGRAMMING PROCEDURE 3/4

14. | Turn the key to the Ignition ON/RUN position.
 The YELLOW LED will turn OFF.
 The RED and YELLOW LEDs will alternate.
---|---
15.| Turn the key to the OFF position.

KEY BYPASS PROGRAMMING PROCEDURE 4/4

AFTER DCRYPTOR PROGRAMMING COMPLETED
Go back to the vehicle and reconnect the 6-Pin (MainHarness) connector and after all the remaining connector.
The module is now programmed.

REMOTE STARTER
Test the remote starter. Remote start the vehicle.
NOTE
IF PROGRAMMING IS INTERRUPTED DURING THE PROCESS, SUCH AS A MODULE IS DISCONNECTED OR BY TURNING OFF THE IGNITION WITH THE KEY, IT IS POSSIBLE THAT THE VEHICLE WILL NO LONGER START NORMALLY, YOU MUST DISCONNECT AND RECONNECT THE VEHICLE BATTERY TO CORRECT THE SITUATION.

REMOTE STARTER FUNCTIONALITY

MANUAL TRANSMISSION: BY DEFAULT

TAKE OVER AUTOMATIQUE TRANSMISSION

REMOTE STARTER PROGRAMMING PROCEDURE

REFER TO THE QUICK INSTALL GUIDE INCLUDED WITH THE MODULE FOR THE REMOTE STARTER PROGRAMMING.

Notice: Updated Firmware and Installation Guides Updated firmware and installation guides are posted on our web site on a regular basis. We recommend that you update this module to the latest fi rmware and download the latest installation guide(s) prior to the installation of this product.
WARNING
The information on this sheet is provided on an (as is) basis with no representation or warranty of accuracy whatsoever.
It is the sole responsibility of the installer to check and verify any circuit before connecting to it. Only a computer safe  logic probe or digital multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or responsibility whatsoever pertaining to the accuracy or currency of the information supplied. The installation in every case is the sole responsibility of the installer performing the work and FORTIN ELECTRONIC SYSTEMS assumes no liability or responsibility whatsoever resulting from any type of installation, whether performed properly, improperly or any other way. Neither the manufacturer or distributor of this module is responsible of damages of any kind indirectly or directly caused by this module, except for the replacement of this module in case of manufacturing defects. This module must be installed by qualifi ed technician. The information supplied is a guide only. This instruction guide may change without notice. Visit www.fortinbypass.com to get the latest version.

TECH SUPPORT
Tél: 514-255-HELP (4357)
1-877-336-7797
ADDENDUM GUIDE
www.fortinbypass.com
WEB UPDATE

References

• Over

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>