FORTIN 94791 Lincoln MKX 2011 Standard Key Remote Starters and Alarm Systems Installation Guide

FORTIN 94791 Lincoln MKX 2011 Standard Key Remote Starters and Alarm Systems Installation Guide

REGULAR, THAR-FOR4 & THAR-FOR1 INSTALLATION

| Vehicle functions supported in this diagram (functional if equipped)
---|---
VEHICLE VEHICULES| YEARS ANNÉES| Immobilizer bypass| T-Harness available (sold separately))| Lock| Unlock| Arm| Disarm| RAP Disable| Parking Lights| Tachometer| Door Status| Trunk Status| Hood Status*| Hand-Brake Status| Foot- Brake Status| OEM Remote monitoring
FORD
Edge| 80-bits (SA KEY)| 2011-2014| •| •| •| •| •| •| •| •| •| •| •| •| •| •| •
LINCOLN
MKX| 80-bits (SA KEY)| 2011-2013| •| •| •| •| •| •| •| •| •| •| •| •| •| •| •

FIRMWARE VERSION VERSION LOGICIELLE

71.[52] MINIMUM

To add the firmware version and the options, use the FLASH LINK UPDATER or FLASH LINK MOBILE tool, sold separately.

trigger (Output Status).
---|---|---|---

MANDATORY INSTAL

HOOD PIN

HOOD STATUS : THE HOOD PIN SWITCH MUST BE INSTALLED IF THE VEHICLE CAN BE REMOTE STARTED WITH THE HOOD OPEN, SET FUNCTION A11 TO OFF

Notice: the installation of safety elements are mandatory. The hood pin is an essential security element and must be installed.

HIS MODULE MUST BE INSTALLED BY A QUALIFIED TECHNICIAN. A WRONG CONNECTION CAN CAUSE PERMANENT DAMAGE TO THE VEHICLE.

DESCRIPTION

T-HARNESS: 12V BATTERY ATTENTION THE T-HARNESS CURRENT IS LIMITED AT 10 AMP MAXIMUM.

If the parking lights (+) require more than 10Amp. connect the remote- starter’s power directly to the vehicles battery with the appropriate fuse.

Some remote starters can not be powered through Data-Link. In these cases connect the remote starter’s fused 12V power wire directly to the T-Harness.

WIRING CONNECTION

THAR-FOR4 – INSTALLATION WIRING

THAR-FOR1 – INSTALLATION WIRING

KEY BYPASS PROGRAMMING PROCEDURE 1/2

Press and hold the programming button:
Connect the 4-PIN Data-link harness (Black connector).

• The Blue, Red, Yellow and Blue & Red LEDs will alternatively illuminate
  

Release the programming button when the LED are BLUE & RED.

• If the LED are not solid BLUE and RED disconnect the 4- Pin connector (Data-Link) and go back to step 7.

Insert the required remaining connectors.

Turn the first functional key to the Ignition ON/RUN position.
Wait 3 seconds.

Turn the key to the OFF position.
and remove the first key

Turn the second functional key to the Ignition ON/RUN position.
Wait 3 seconds.

Turn the key to the OFF position.
and remove the second key.

Turn the key to the Ignition ON/RUN position.
The RED AND BLUE LED will flash rapidly ten (10) times. Key bypass programmed.
Wait

• The BLUE LED will flash rapidly. CAN-Bus programmed
  

Turn the Ignition to the OF position.

• The BLUE LED will turn off.
• The YELLOW LED will turn on.
  

The module is now programmed.

Use the remote of the remote  starter or security system to test all of the supported features to ensure proper programming.

REMOTE STARTER FUNCTIONALITY

• All doors must be closed.

• Remote start the vehicle.

• Unlock the doors with the remote-starter remote or the OEM remote.

• Insert and Turn the key to the Ignition ON/RUN position.

• Press the brake pedal.

• The vehicle can now be put in to gear and driven.

Notice: Updated Firmware and Installation Guides Updated fi rmware and installation guides are posted on our web site on a regular basis. We recommend that you update this module to the latest firmware anddownload the latest installation guide(s) prior to the installation of this product.

WARNING
The information on this sheet is provided on an (as is) basis with no representation or warranty of accuracy whatsoever. It is the sole responsibility of the installer to check and verify any circuit before connecting to it. Only a computer safe logic probe or digital multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or responsibility whatsoever pertaining to the accuracy or currency of the information supplied. The installation in every case is the sole responsibility of the installer performing the work and FORTIN ELECTRONIC SYSTEMS assumes no liability or responsibility whatsoever resulting from any type of installation, whether performed properly, improperly or any other way. Neither the manufacturer or distributor of this module is responsible of damages of any kind indirectly or directly caused by this module, except for the replacement of this module in case of manufacturing defects. This module must be installed by qualified technician. The information supplied is a guide only. This instruction guide may change without notice. Visit www.fortinbypass.com to get the latest version.

TECH SUPPORT
Tell: 514-255-HELP (4357) 1-877-336-7797

ADDENDUM GUIDE

www.fortinbypass.com
WEB UPDATE

References

• Home | Marcelino d.o.o.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>