FORTIN 90451 2017 Chevrolet Spark Regular Key Remote Starters And Alarm Systems Installation Guide

FORTIN 90451 2017 Chevrolet Spark Regular Key Remote Starters And Alarm Systems Installation Guide

REGULAR INSTALLATION

ADDENDUM – SUGGESTED WIRING CONFIGURATION

| Vehicle functions supported in this diagram (functional if equipped)
---|---
VEHICLE| YEARS
CHEVROLET
Cantonment| T-Harness available| Lock| Unlock| Arm| Disarm| Trunk (open)| RAP Disable| Tachometer| Door Status| Trunk Status0| Hood Status*| Hand-Brake Status| Foot-Brake Status| PK3, Passlock| OEM remote Monitoring**
Spark| Key 2016-2019| •| •| •| •| •| •| •| •| •| •| •| •| •| •| •| •

FIRMWARE VERSIO 70.[41] To add the firmware version and the options, use the FLASH LINK UPDATER or FLASH LINK MOBILE tool, sold separately
The vehicles Flip-key remote will not be  functional during remote start.
Parts required (Not included)
1X 1 Amp Diode
1X Compatible DATA-LINK remote starter
1X 180 Ohm resistor (Manual transmission)

MANDATORY INSTALL

• HOOD PIN ****	HOOD STATUS : THE HOOD PIN SWITCH MUST BE INSTALLED IF THE VEHICLE CAN BE REMOTE STARTED WITH THE HOOD OPEN, SET FUNCTION A11 TO OFF.	A11	OFF NON	Notice: the installation of safety elements are mandatory. The hood pin is an essential security element and must be installed.	THIS MODULE MUST BE INSTALLED BY A QUALIFIED TECHNICIAN. A WRONG CONNECTION CAN CAUSE PERMANENT DAMAGE TO THE VEHICLE.

NOTES

| Program bypass option:| UNIT OPTIO| DESCRIPTION
---|---|---|---
IF THE VEHICLE IS NOT EQUIPPED WITH FUNCTIONAL HOOD PIN:| C1| OEM Remote status (Lock/Unlock) monitoring
Program bypass option (If equiped with OEM alarm):| A11| OFF NON| Hood trigger (Output Status).
| | D2| Unlock before / Lock after (Disarm OEM alarm)
E5| OFF NON| SPECIAL FUNCTIONS: BY DEFAULT DEACTIVATED FONCTION SPECIALE
ON OUI| MANUFACTURED MODULES BETWEEN: 04/2018 TO 04/2019

DESCRIPTION

AT IGNITION SWITCH

AUTOMATIC TRANSMISSION WIRING CONNECTION

MANUAL TRANSMISSION WIRING CONNECTION

DCRYPTOR PROGRAMMING PROCEDURE

Parts required (not included)

1x FLASH LINK UPDATER,
1x FLASH LINK MANAGER
Microsoft Windows Computer with Internet connection 1x Ordinateur Microsoft Windows avec connection Internet

OR
OU

1x FLASH LINK MOBILE
1x FLASH LINK MOBILE APP
1x Smartphone Android or iOS with Internet connection (Internet provider charges may apply) Téléphone Intelligent Android ou iOS avec connection

BEFORE PROGRAMMING SET THE UNIT OPTIONS AND SAVE.

1. Press and hold the programming button: Connect the 4-PIN Data-link harness (Black connector). The Blue, Red, Yellow and Blue & Red LEDs will alternatively illuminate.
   

2. Release the programming button when the LED is YELLOW
   
   If the LED is not solid YELLOW disconnect the 4-Pin connector (Data-Link) and go back to step 1.

3. Insert the required remaining connectors.
   

4. Press and release the programming button five times (5x).

   • The YELLOW LED will alternate between 5x flashes and a pause.
   • Wait until the YELLOW LED turns ON
     

5. Turn the key to the Ignition ON/RUN position

   • The RED LED will turns ON.
     The YELLOW LED turns
     OFF.
     
     If the LED is not solid RED disconnect the 4-Pin connector (Data-Link) and go back to step 1.

6. Turn the key to the
   OFF position.

7. Remove the key from the Ignition barrel.

CONTINUED NEXT PAG
EKEY BYPASS PROGRAMMING PROCEDURE 2/2

8. Wait 5 seconds.

9. 
   Turn the Ignition to the ON position.

   • The BLUE LED will turns ON.
   • Wait, the BLUE & RED LED will turns OFF.
   • Wait, the YELLOW LED will Flash.
   • Wait, the YELLOW LED will turns OFF.
   • Wait, the BLUE LED will Flash rapidly.
     If the LEDs do not react as shown, disconnect the 4-Pin connector (Data-Link) and go back to step 1.

10. 
    Turn the key to the OFF position

    • The BLUE LED flash slowly.

11. 
    Disconnect all the connectors and after the Data-Link (4-pins) connector

12. 
    FLASH LINK UPDATER                            FLASH LINK MANAGER
    SOFTWARE | PROGRAMME
    Microsoft Windows Computer with Internet connection
    Ordinateur Microsoft Windows avec connection Internet
    Use the tool:
    FLASH LINK UPDATER or FLASH LINK MOBILE to visit the DCryptor menu.
    OR
    OU
    
    Smartphone (Internet provider charges may apply)
    *Parts required (not included)

13. 
    AFTER DCRYPTOR PROGRAMMING COMPLETED
    Go back to the vehicle and reconnect the 4-Pin (Data-Link) connector and after, all the remaining connector.

The module is now programmed.
REMOTE STARTER / ALARM VERIFICATION PROCEDURE | PROCÉDURE DE VÉRIFICATION DU DÉMARREUR À DISTANCE / ALARME
Test the remote starter. Remote start the vehicle.

REMOTE STARTER FUNCTIONALITY

• All doors must be closed.

• Remote start the vehicle

• Unlock the doors with the remote-starter remote or the OEM remote.

• Insert and Turn the key to the Ignition ON/RUN position.

• Press the brake pedal.

• The vehicle can now be put in to gear and driven

This guide may change without notice. See www.fortin.ca for latest version.

HARDWARE VERSION
FIRMWARE VERSION
Date: xx-x

EVO-ALL
INTERFACE MODULE
Made in Canada
Service No :
PATENTS PENDING US: 2007-228827-A1
www.fortinbypass.com
000 102 04 253
Module label

Notice: Updated Firmware and Installation Guides
Updated fi rmware and installation guides are posted on our web site on a regular basis. We recommend that you update this module to the latest fi rmware and download the latest installation guide(s) prior to the installation of this product.

WARNING
The information on this sheet is provided on an (as is) basis with no representation or warranty of accuracy whatsoever. It is the sole responsibility of the installer to check and verify any circuit before connecting to it. Only a computer safe logic probe or digital multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or responsibility whatsoever pertaining to the accuracy or currency of the information supplied. The installation in every case is the sole responsibility of the installer performing the work and FORTIN ELECTRONIC SYSTEMS assumes no liability or responsibility whatsoever resulting from any type of installation, whether performed properly, improperly or any other way. Neither the manufacturer or distributor of this module is responsible of damages of any kind indirectly or directly caused by this module, except for the replacement of this module in case of manufacturing defects. This module must be installed by qualifi ed technician. The information supplied is a guide only. This instruction guide may change without notice. Visit www.fortinbypass.com to get the latest version.

Copyright © 2006-2018, FORTIN AUTO RADIO INC ALL RIGHTS RESERVED PATENT PENDING

TECH SUPPORT
Tél: 514-255-HELP (4357)
1-877-336-7797
ADDENDUM GUIDE
****
www.fortinbypass.com
WEB UPDATE | MISE À JOUR INTERNET

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>