FORTIN 103481 THAR-CHR4 2014 Chrysler Town and Country Push Button Remote Starters and Alarm Systems Installation Guide

: June 13, 2024
: FORTIN

Table of Contents

FORTIN 103481 THAR-CHR4 2014 Chrysler Town and Country Push Button Remote
Vehicle functions
MANDATORY INSTALL
DIAGRAM
PARTS REQUIRED
STAND ALONE CONFIGURATION
REMOTE STARTER FUNCTIONALITY
REMOTE STARTER WARNING CARD
WIRING CONNECTIONS
PROGRAMMING PROCEDURE
Contact
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

FORTIN 103481 THAR-CHR4 2014 Chrysler Town and Country Push Button Remote

Starters and Alarm Systems

WARNING: ONLY COMPATIBLE WITH AUTOMATIC TRANSMISSION VEHICLES.

Vehicle functions

| FIRMWARE VERSION VERSION LOGICIELLE 59.[01] MINIMUM| To add the firmware version and the options, use the FLASH LINK UPDATER or FLASH LINK MOBILE tool, sold separately.
---|---|---

UNIT OPTION

| Program bypass option:| UNIT OPTION| DESCRIPTION
---|---|---|---
C1| OEM Remote status (Lock/Unlock) monitoring
IF THE VEHICLE IS NOT EQUIPPED WITH FUNCTIONAL HOOD PIN:| A11|

OFF

| Hood trigger (Output Status).
Contact de capot (état de sortie).
Program bypass option ( If equiped with OEM alarm ):| D2| Unlock before / Lock after (Disarm OEM alarm)
| D6| Push-to-Start
Push-to-Start
Program bypass option

( Vehicle diesel only ) :

| D1.3| Diesel mode (Vehicle diesel only)

Parts required

Parts required (Not included)
- 1X 1.5k Ohm Resistor

MANDATORY INSTALL

HOOD PIN HOOD STATUS: THE HOOD PIN SWITCH MUST BE INSTALLED IF THE VEHICLE CAN BE REMOTE STARTED WITH THE HOOD OPEN, SET FUNCTION A11 TO OFF.
A11: OFF

Notice: the installation of safety elements are mandatory. The hood pin is an essential security element and must be installed. THIS MODULE MUST BE INSTALLED BY A QUALIFIED TECHNICIAN. A WRONG CONNECTION CAN CAUSE PERMANENT DAMAGE TO THE VEHICLE.

NOTES 12V BATTERY FOR T-HARNESS

ATTENTION: THE T-HARNESS CURRENT IS LIMITED AT 10 AMP MAXIMUM.

If a parking lights (+) wire is use : they require more than 10Amp. Connect the remote-starter’s power directly to the vehicles battery with the appropriate fuse.
Some remote starters can not be powered through Data-Link.
In these cases connect the remote starter’s fused 12V power wire directly to the T-Harness.

DIAGRAM

WIRE TO WIRE Connection Diagram
THAR-CHR4 – THarness Diagram

PARTS REQUIRED

PARTS REQUIRED (NOT INCLUDED)

FLASH LINK UPDATER, FLASH LINK MANAGER
Microsoft Windows Computer with Internet connection Ordinateur Microsoft Windows avec connection Internet

FLASH LINK MOBILE FLASH LINK MOBILE APP

Smartphone AndroId or iOS with Internet connection (provider charges may apply).

MANDATORY

HOOD PIN
- REMOTE START SAFETY OVERRIDE SWITCH
- VALET SWITCH COMMUTATEUR VALET

Part #: RSPB available, Sold separately.

Notice: the installation of safety elements are mandatory. The hood pin and the valet switch are essential security elements and must be installed.

STAND ALONE CONFIGURATION

Program bypass option
- OEM Remote Stand Alone Remote Starter:

UNIT OPTION/ DESCRIPTION

D1.10/ By default, LOCK, LOCK, LOCK
D1.1/ LOCK, UNLOCK, LOCK

| Program bypass option with oem remote:| UNIT OPTION| DESCRIPTION
---|---|---|---
C1| OEM Remote Monitoring

| ****

Program bypass option with RF KIT antenna:

| UNIT OPTION| DESCRIPTION
---|---|---|---
H1 to H6| Supported RF Kits and select RF Kit

REMOTE STARTER FUNCTIONALITY

All doors must be closed.
Press the OEM remote’s Lock button 3x to remote-start (or remote-stop) the vehicle.
The vehicle will START.

REMOTE STARTER DIAGNOSTICS

MODULE RED LED

x2 flash: Brake ON
x3 flash: No tach
x4 flash: Ignition before start
x5 flash: Hood Open

REMOTE STARTER WARNING CARD

CUT THIS WARNING CARD AND STICK IT ON A VISIBLE PLACE:

or use the package RSPB, Sold separately.

WARNING: REMOTE STARTER

THE VEHICLE CAN BE STARTED BY EITHER: PRESSING THE LOCK BUTTON ON THE OEM REMOTE 3 TIMES CONSECUTIVELY OR BY A SMARTPHONE. TURN ON THE SAFETY SWITCH LOCATED UNDER THE DASHBOARD BEFORE WORKING ON THE VEHICLE.

WIRING CONNECTIONS

AUTOMATIC TRANSMISSION WIRING CONNECTION

THAR-CHR4 – AUTOMATIC TRANSMISSION WIRING CONNECTION

PROGRAMMING PROCEDURE

Press and hold Insert the programming button: the 4-Pin (Data-Link) connector.
- The Blue, Red, Yellow and Blue & Red LEDs will alternatively illuminate.
Release the programming button when the LED is BLUE. If the LED is not solid BLUE disconnect the 4-Pin connector (Data-Link) and go back to step 1.
Insert the required remaining connectors.
Do not press the brake pedal. Press the Push-to-Start button twice to turn ON the ignition.
- The BLUE LED will flash rapidly.
Press the Push-to-Start button once to turn off theignition.
- The BLUE LED will flash rapidly.

Press the LOCK button on the vehicles OEM remote.
Press and release the programming button on the once.
The BLUE LED will turn off.

The module is now programmed

Use the remote of the remote starter or security system to test all of the supported features to ensure proper programming.

REMOTE STARTER FUNCTIONALITY

All doors must be closed.
Remote start the vehicle.
Unlock the doors with either: The OEM remote or The remote-starter remote
Enter the vehicle with the SMART-KEY.
Press the Push-to-Start button twice to turn ON the ignition.
The vehicle can now be put in to gear and driven.

Notice: Updated Firmware and Installation Guides

Updated firmware and installation guides are posted on our web site on a regular basis. We recommend that you update this module to the latest firmware and download the latest installation guide(s) prior to the installation of this product.

Module label

WARNING

The information on this sheet is provided on an (as is) basis with no representation or warranty of accuracy whatsoever. It is the sole responsibility of the installer to check and verify any circuit before connecting to it. Only a computer safe logic probe or digital multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or responsibility whatsoever pertaining to the accuracy or currency of the information supplied. The installation in every case is the sole responsibility of the installer performing the work and FORTIN ELECTRONIC SYSTEMS assumes no liability or responsibility whatsoever resulting from any type of installation, whether performed properly, improperly or any other way. Neither the manufacturer or distributor of this module is responsible of damages of any kind indirectly or directly caused by this module, except for the replacement of this module in case of manufacturing defects. This module must be installed by qualifi ed technician. The information supplied is a guide only. This instruction guide may change without notice. Visit www.fortinbypass.com to get the latest version.