FORTIN 97381 Volkswagen Touareg 2012 Regular Key Remote Starters and Alarm Systems Instruction Manual

97381 Volkswagen Touareg 2012 Regular Key Remote Starters and Alarm

Systems

REGULAR & THAR-AUD1 INSTALLATION

ADDENDUM – SUGGESTED WIRING CONFIGURATION

| Vehicle functions supported in this diagram (functional if equipped) |
---|---
VEHICLE| YEARS| Immobilizer bypass| Lock| Unlock| Arm| Disarm| Tachometer| Trunk Release| Door Status| Trunk Status| Hood Status*| Hand-Brake Status| Foot-Brake Status|

OEM Remote monitoring**

Touareg| 2011-2017| •| •| •| •| •| •| •| •| •| •| •| •| •

COMPATIBLE
MODULE
REQUIRED:

| QR CODE
ON THE LABEL|

FIRMWARE VERSION
VERSION LOGICIELLE

|

To add the firmware version and the options, use the
FLASH LINK UPDATER or FLASH LINK MOBILE tool,
sold separately

---|---|---|---
MANUFACTURED
AFTER: 2019

NOTES

**OEM Remote Monitoring The vehicles OEM remote will remain
functional when the vehicle is running,
however, the intelligent access key will not
unlock the doors when the vehicle is running.

Parts required (Not included)

WIRE TO WIRE DIAGRAM
1x 10Amp Fuse
3x 1 AMP Diode
1x Relay for key release

THARNESS DIAGRAM
THARNESS THAR-AUD1
1x THAR-AUD1
1x THAR-AUD1

MANDATORY INSTALL

HOOD STATUS : THE HOOD PIN SWITCH MUST BE INSTALLED
IF THE VEHICLE CAN BE REMOTE STARTED WITH THE HOOD OPEN,
SET FUNCTION A11 TO OFF.

Notice: the installation of safety
elements are mandatory. The hood pin
is an essential security element and
must be installed.

THIS MODULE MUST BE INSTALLED BY A
QUALIFIED TECHNICIAN. A WRONG
CONNECTION CAN CAUSE PERMANENT
DAMAGE TO THE VEHICLE.

This guide may change without notice. See www.fortin.ca for latest version.

NOTES

| UNIT OPTION| DESCRIPTION
---|---|---
| Program bypass option:| C1|

OEM Remote status (Lock/Unlock)
monitoring

| D6| Push-to-Start
D5| Lock after start
E4|

FEATURE 1 :
Disarm OEM alarm with transponder

| IF THE VEHICLE IS NOT EQUIPPED
WITH FUNCTIONAL HOOD PIN:| A11 off non|

Hood trigger (Output Status).

Program bypass option
(Vehicle diesel only):| D1.3|

Diesel mode (Vehicle diesel only)

This guide may change without notice. See www.fortin.ca for latest version.

DESCRIPTION

1. Ignition switch Connector

REMOVE THE PLASTIC PROTECTIVE CAP OVER THE KEY PORT TO SEE THE WIRE LOCATION.

2. BCM, left of steering column, white connector with grey cover.

This guide may change without notice. See www.fortin.ca for latest version.

AUTOMATIC TRANSMISSION WIRING CONNECTION

This guide may change without notice. See www.fortin.ca for latest version.

THAR-AUD1 | AUTOMATIC TRANSMISSION CONNECTION

This guide may change without notice. See www.fortin.ca for latest version.

DCRYPTOR PROGRAMMING PROCEDURE

Parts required (not included)

1x FLASH LINK UPDATER,
1x FLASH LINK MANAGER SOFTWARE
1x Microsoft Windows Computer with Internet connection

BEFORE PROGRAMMING SET THE UNIT OPTIONS AND SAVE.

Insert the key in the Key port

1 Press and hold Insert the programming button:
the 4-Pin (Data-Link) connector.

The Blue, Red, Yellow and Blue & Red LEDs will
alternatively illuminate.

2 Release the programming
button when the LED is BLUE.

If the LED is not solid BLUE
disconnect the 4-Pin connector
(Data-Link) and go back to step 1.

3 Insert the required remaining
connectors.

4  Turn the key to turn ignition ON.

5 Press and release the
programming button once
(1x).

The BLUE LED will turn off.

The BLUE LED will flash
rapidly.

KEY BYPASS PROGRAMMING PROCEDURE 2/3

Press and Hold the
programming button.

Wait until the RED LED will
turn ON solid.

The BLUE LED will turn OFF.

Release the programming
button.

The LEDs will alternate
between BLUE, YELLOW and
RED flashes.

Wait,

The vehicle ignition turn ON
than OFF a few times.

DO NOT TOUCH THE VEHICLE.

Wait,

The vehicle ignition will turn ON .

The RED and YELLOW
LEDs will alternate.

Turn the key to shut off the ignition.

KEY BYPASS PROGRAMMING PROCEDURE 3/3

 8 Disconnect all the connectors and after
the Data-Link (4-pins) connector.

9 Use the tool:
FLASH LINK UPDATER or
FLASH LINK MOBILE
to visit the DCryptor menu.

10 AFTER DCRYPTOR PROGRAMMING COMPLETED
Go back to the vehicle and reconnect the 4-Pin (Data-Link)
connector and after, all the remaining connector.

The module is now programmed.

REMOTE STARTER / ALARM VERIFICATION

Test the remote starter. Remote start the vehicle.

This guide may change without notice. See www.fortin.ca for latest version.

REMOTE STARTER FUNCTIONALITY

Vehicles with key port.

Vehicles with Push-to-Start.

Notice: Updated Firmware and Installation Guides
Updated firmware and installation guides are posted on our web site on a regular
basis. We recommend that you update this module to the latest fi rmware and
download the latest installation guide(s) prior to the installation of this product.

WARNING
The information on this sheet is provided on an (as is) basis with no representation or warranty of accuracy whatsoever.
It is the sole responsibility of the installer to check and verify any circuit before connecting to it. Only a computer safe
logic probe or digital multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or
responsibility whatsoever pertaining to the accuracy or currency of the information supplied. The installation in every case
is the sole responsibility of the installer performing the work and FORTIN ELECTRONIC SYSTEMS assumes no liability
or responsibility whatsoever resulting from any type of installation, whether performed properly, improperly or any other
way. Neither the manufacturer or distributor of this module is responsible of damages of any kind indirectly or directly
caused by this module, except for the replacement of this module in case of manufacturing defects. This module must be
installed by qualifi ed technician. The information supplied is a guide only. This instruction guide may change without
notice. Visit www.fortinbypass.com to get the latest version.

TECH SUPPORT
Tél: 514-255-HELP (4357)
1-877-336-7797
ADDENDUM GUIDE

www.fortinbypass.com

WEB UPDATE

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>