FORTIN 80581 Mazda 6 2011 Standard Key Remote Starters and Alarm Systems Instruction Manual
- June 13, 2024
- FORTIN
Table of Contents
** REGULAR INSTALLATION
ADDENDUM – SUGGESTED WIRING CONFIGURATION**
80711 2005 Mazda 6 Regular Key Remote Starters and Alarm Systems
“Vehicle functions supported in this diagram (functional if equipped)
| FIRMWARE VERSION
71.[44] FORD MINIMUM| To add the firmware version and the options, use the
FLASH LINK UPDATER or FLASH LINK MOBILE tool, sold separately.
---|---|---
| Program bypass option
IF THE VEHICLE IS NOT EQUIPPED WITH FUNCTIONAL HOOD PIN:| UNIT OPTION
OPTION UNITE| DESCRIPTION
---|---|---|---
A11| | Hood trigger (Output Status).
| Program bypass option
(If equiped with OEM alarm):| UNIT OPTION
OPTION UNITE| DESCRIPTION
---|---|---|---
D2| Unlock before / Lock after (Disarm OEM alarm)
Parts required (Not included)
1X 1 K Ohm Resistorode
MANDATORY INSTALL
* HOOD PIN HOOD STATUS: THE HOOD PIN SWITCH MUST BE INSTALLED IF
THE VEHICLE CAN BE REMOTE STARTED WITH THE HOOD OPEN, SET FUNCTION A11 TO OFF.
A11|
---|---
Notice: the installation of safety elements are mandatory. The hood pin
is an essential security element and must be installed.
THIS MODULE MUST BE INSTALLED BY A QUALIFIED TECHNICIAN. A WRONG CONNECTION
CAN CAUSE PERMANENT DAMAGE TO THE VEHICLE.
DESCRIPTION
WIRING CONNECTION
KEY BYPASS PROGRAMMING PROCEDURE 2/3
Make sure to have two valide vehicle key.
Press and hold the programming button:
Insert the 4-Pin (Data-Link) connector.
The Blue, Red, Yellow and Blue & Red LEDs will alternatively
illuminate.
Release the programming button when the LED is
RED.
If the LED is not solid RED disconnect the 4-Pin connector (Data-Link) and go
back to step 1.
Insert the required remaining connectors.
Turn the first functIonal key to the ON/RUN
position.
Wait 3 seconds or until the security light turns OFF. CAUTION The
following step must be completed within 5 seconds. Otherwise disconnect all
connectors and go back to step 1. 
Turn the ignition to the OFF position and remove
the first key.
Wait 3 seconds. Turn the second functIonal key to the ON/RUN position.
Wait 3 seconds or until the security light turns OFF. Turn the ignition to the
OFF position and remove the second key.
CONTINUED NEXT PAGE
KEY BYPASS PROGRAMMING PROCEDURE 3/3 CAUTION The following step must be
completed within 5 seconds. Otherwise disconnect all connectors and go back to
step 1.
AUTOMATIC TRANSMISSION Activate the remote starter.
MANUAL TRANSMISSION
Press and hold the programming button
untithe LED flashes once than release the programming button.
The RED LED will flash once (1x). 9. Using a jumper wire, apply power (12v) to
the vehicle’s ignition1.
10. The RED LED will flash rapidly ten
(10) times and after the BLUE LED will flash rapidly.
If the LED is solid RED disconnect the 6 Pin connector (Main-Harness) and go
back to step 1.
11. MANUAL TRANSMISSION Remove the jumper.
12. The BLUE LED will turn off.
Manual transmission:
Remove the jumper.
The module is now programmed.
Use the remote of the remote starter or security system to test all of the
supported features to ensure proper programming.
DCRYPTOR PROGRAMMING PROCEDURE
Parts required (not included)
FLASH LINK UPDATER,
FLASH LINK MANAGER
SOFTWARE | PROGRAMME
Microsoft Windows Computer with Internet connection
Ordinateur Microsoft Windows avec connection Internet
OR
OU
FLASH LINK MOBILE
FLASH LINK MOBILE APP
Smartphone Android or iOS with Internet connection (Internet provider charges
may apply)
BEFORE PROGRAMMING SET THE UNIT OPTIONS AND SAVE.
Press and hold Insert the programming
button: the 4-Pin (Data-Link) connector.
The Blue, Red, Yellow and Blue & Red LEDs will alternatively
illuminate.
Release the programming button when the LED
is RED.
Insert the required remaining
connectors.
Press and release the programming button once
(1x).
The RED LED will flash once.
Turn the Ignition to the ON/RUN position.
WAITthe RED LED will turn OFF.
The YELLOW LED will turn on.
Turn the Ignition to the OFF position.
WAITthe YELLOW LED will turn OFF.
KEY BYPASS PROGRAMMING PROCEDURE 2/2
Turn the Ignition to the ON/RUN position.
The RED and YELLOW LEDs will alternate. Turn the Ignition to the OFF
position.
Disconnect all the connectors and after the
Data-Link (4-pins) connector.
Use the tool:
FLASH LINK UPDATER or FLASH LINK MOBILE to visit the DCryptor menu.
*Parts required (not included)
AFTER DCRYPTOR PROGRAMMING COMPLETED Go back to the vehicle and reconnect the 4-Pin (Data-Link) connector and after, all the remaining connector.
The module is now programmed.
REMOTE STARTER / ALARM VERIFICATION
Test the remote starter. Remote start the vehicle.
REMOTE STARTER FUNCTIONALITY
| |
---|---|---
All doors must be closed.| Remote start the vehicle.| Unlock the doors with
the remote-starter remote or the OEM remote.
| |
Insert and Turn the key to the Ignition ON/RUN position.| Press the brake
pedal.| The vehicle can now be put in to gear and driven.
www.fortinbypass.com
Notice: Updated Firmware and Installation Guides
Updated fi rmware and installation guides are posted on our web site on a
regular basis. We recommend that you update this module to the latest fi rmware
and download the latest installation guide(s) prior to the installation of
this product.
WARNING
The information on this sheet is provided on an (as is) basis with no
representation or warranty of accuracy whatsoever. It is the sole
responsibility of the installer to check and verify any circuit before
connecting to it. Only a computer safe logic probe or digital multimeter
should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or
responsibility whatsoever pertaining to the accuracy or currency of the
information supplied. The installation in every case is the sole
responsibility of the installer performing the work and FORTIN ELECTRONIC
SYSTEMS assumes no liability or responsibility whatsoever resulting from any
type of installation, whether performed properly, improperly or any other way.
Neither the manufacturer or distributor of this module is responsible of
damages of any kind indirectly or directly caused by this module, except for
the replacement of this module in case of manufacturing defects. This module
must be installed by qualifi ed technician. The information supplied is a guide
only. This instruction guide may change without notice. Visit
www.fortinbypass.com to get the latest version.
TECH SUPPORT
Tél: 514-255-HELP (4357)
1-877-336-7797
ADDENDUM GUIDE
www.fortinbypass.com
WEB UPDATE
REV.: 20220107
Guide # 80711
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>