FORTIN 80401 Mazda 2 2011 Standard Key Remote Starters and Alarm Systems Installation Guide

REV.: 20211217
Guide # 80401
REGULAR INSTALLATION
ADDENDUM – SUGGESTED WIRING CONFIGURATION

BYPASS FIRMWARE VERSION
VERSION LOGICIELLE CONTOURNEMENT
71.[44] MINIMUM

| Program remote starter option:| FUNCTION| MODE| DESCRIPTION
---|---|---|---|---
| | 6| 2| Unlock before remote-start & Lock after remote-start.
| | 8| 5| Unlock Pulse Time : Single 1.5 sec
| Program bypass option:| UNIT OPTION C1| OEM Remote status (Lock/Unlock) monitoring
| IF THE VEHICLE IS NOT EQUIPPED WITH FUNCTIONAL HOOD PIN:| A11| | Hood trigger (Output Status).

MANDATORY INSTALL

• HOOD PIN

HOOD STATUS: THE HOOD PIN SWITCH (INCLUDED) MUST BE INSTALLED IF THE VEHICLE CAN BE REMOTE STARTED WITH THE HOOD OPEN, SET FUNCTION All TO OFF.

A11|
---|---

SECURITY STICKER

Notice: the installation of safety elements are mandatory. The hood pin and the sticker are essential security elements and must be installed.
THIS MODULE MUST BE INSTALLED BY A QUALIFIED TECHNICIAN. A WRONG CONNECTION CAN CAUSE PERMANENT DAMAGE TO THE VEHICLE.

DESCRIPTION

WIRING CONNECTION

KEY BYPASS PROGRAMMING PROCEDURE 1/2

Make sure to have two valide vehicle key.

1. Press and hold the Insert programming button: the 6-Pin Main connector.
   ↳  The LEDs will alternate between BLUE, RED, YELLOW & BLUE/RED flashes.
   

2. Release the programming button when the LED is RED.
   If the LED is not solid RED disconnect the 6 Pin connector (Main-Harness) and go back to step 1.
   

3. Insert the required remaining connectors.
   

4. Turn the first functIonal key to the ON/RUN position.
   Wait 3 seconds or until the security light turns OFF.
   

5. CAUTION The following step must be completed within 5 seconds.  Otherwise disconnect all connectors and go back to step 1.
   5 sec. max
   Turn the ignition to the OFF position and remove the first key.
   Wait 3 seconds.

6. Turn the second functIonal key to the ON/RUN position.
   Wait 3 seconds or until the security light turns OFF.
   

7. Turn the ignition to the OFF position and remove the second key.
   
   KEY BYPASS PROGRAMMING PROCEDURE 3/3

8. CAUTION The following step must be completed within 5 seconds.
   Otherwise disconnect all connectors and go back to step 1.
   AUTOMATIC TRANSMISSION
   Activate the remote starter.

MANUAL TRANSMISSION

Press and hold the programming button until the LED flashes once than release the programming button.
↳ The RED LED will flash once (1x).

9. Using a jumper wire, apply (12v) to the vehicle’s ignition1. power

10. The RED LED will flash rapidly ten (10) times and after the BLUE LED will flash rapidly.
    If the LED is solid RED disconnect the 6 Pin connector (Main-Harness) and go back to step 1.
    

11. MANUAL TRANSMISSION
    Remove the jumper.

12. ↳ The BLUE LED will turn off.
    

Manual transmission:
Remove the jumper.
The module is now programmed.
Use the remote of the remote starter or security system to test all of the supported features to ensure proper programming.

DCRYPTOR PROGRAMMING PROCEDURE

Parts required (not included)
FLASH LINK UPDATER,
FLASH LINK MANAGER
SOFTWARE | PROGRAMME
Microsoft Windows Computer with Internet connection Ordinateur Microsoft Windows avec connection Internet
OR

FLASH LINK MOBILE

FLASH LINK MOBILE APP

Smartphone Android or iOS with Internet connection (Internet provider charges may apply)
BEFORE PROGRAMMING SET THE UNIT OPTIONS AND SAVE.

1. Press and hold Insert the programming button: the 6-Pin Main connector.
   ↳  The LEDs will alternate between BLUE, RED, YELLOW & BLUE/RED flashes.
   

2. Release the programming button when the LED is RED.
   If the LED is not solid RED disconnect the 6 Pin connector (Main-Harness) and go back to step 1.
   

3. Insert the required remaining connectors.
   

4. Press and release the programming button once (1x).
   ↳  The RED LED will flash once.
   

5. Turn the Ignition to the ON/RUN position.
   ↳ WAITthe RED LED will turn OFF.
   ↳ The YELLOW LED will turn on.
   

6. Turn the Ignition to the OFF position.
   ↳ WAITthe YELLOW LED will turn OFF.
   
   KEY BYPASS PROGRAMMING PROCEDURE 2/2

7. Turn the Ignition to the ON/RUN position.
   ↳  The RED and YELLOW LEDs will alternate.
   

8. Turn the Ignition to the OFF position.

9. Disconnect all connectors and after the 6-Pin (Main-Harness) or the 4-Pin Data-link connector.
   

10. Microsoft Windows Computer with Internet connection*
    
    Use the tool:
    FLASH LINK UPDATER or FLASH LINK MOBILE to visit the DCryptor menu.

• Parts required (not included)
  Smartphone*
  (Internet provider charges may apply)
  

  11. AFTER DCRYPTOR PROGRAMMING COMPLETED
      Go back to the vehicle and reconnect the 6-Pin (MainHarness) or the 4-pins (Data-Link) connector and after all the remaining connector.

The module is now programmed.
REMOTE STARTER / ALARM VERIFICATION

REMOTE STARTER PROGRAMMING PROCEDURE

REFER TO THE QUICK INSTALL GUIDE INCLUDED WITH THE MODULE FOR THE REMOTE STARTER PROGRAMMING.

REMOTE STARTER FUNCTIONALITY

| All doors must be closed.
---|---
| Remote start the vehicle.
| Unlock the doors with the remote-starter remote or the OEM remote.
| Insert and Turn the key to the Ignition ON/RUN position.
| Press the brake pedal.
| The vehicle can now be put in to gear and driven.

www.fortinbypass.com
Module label

Notice: Updated Firmware and Installation Guides
Updated firmware and installation guides are posted on our web site on a regular  basis. We recommend that you update this module to the latest fi rmware and download the latest installation guide(s) prior to the installation of this product.
WARNING
The information on this sheet is provided on an (as is) basis with no representation or warranty of accuracy whatsoever. It is the sole responsibility of the installer to check and verify any circuit before connecting to it. Only a computer safe logic probe or digital multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or responsibility whatsoever pertaining to the accuracy or currency of the information supplied. The installation in every case is the sole responsibility of the installer performing the work and FORTIN ELECTRONIC SYSTEMS assumes no liability or responsibility whatsoever resulting from any type of installation, whether performed properly, improperly or any other way. Neither the manufacturer or distributor of this module is responsible of damages of any kind indirectly or directly caused by this module, except for the replacement of this module in case of manufacturing defects. This module must be installed by qualifi ed technician. The information supplied is a guide only. This instruction guide may change without notice. Visit www.fortinbypass.com to get the latest version.
Copyright © 2006-2018, FORTIN AUTO RADIO INC ALL RIGHTS RESERVED PATENT PENDING

TECH SUPPORT
Tél: 514-255-HELP (4357)
1-877-336-7797
Made in canada
ADDENDUM GUIDE
www.fortinbypass.com
WEB UPDATE

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>